The 'umcumgr' is a simple command line tool for MCU firmware management
over MCUmgr/SMP protocol. It will be used together with MCUboot running
on the on-board (or external, e.g. in form of a dongle) MCU.
While at it, add also dedicated 'mcu.yml' profile file.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Mesh++ S618 has below products based on Qualcomm IPQ6018:
* cp03-c1
* cp01-c1
These are Wi-Fi 6 (IEEE 80211.ax) dual band 2x2 mesh routers.
Fixes: WIFI-10561
Signed-off-by: Krishna <krishna@meshplusplus.com>
Signed-off-by: Edward Cheung <edward@meshplusplus.com>
Signed-off-by: Alex Ballmer <alexb@meshplusplus.com>
Device specifications:
======================
* Qualcomm IPQ6000
* 512 MB of RAM
* 64 MB of SPI NOR flash
- 2x 28 MB available; but one of the 28 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11ax)
* 2T2R 5 GHz Wi-Fi (11ax)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board
* 2x ethernet
- eth0
+ 1000 Mbps Ethernet
+ used as LAN interface
- eth1
+ 1000 Mbps Ethernet
+ 802.3at POE
+ used as WAN interface
* 12 2A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
setenv bootargs 'console=ttyMSM0,115200n8 rootfstype=squashfs,jffs2 board=PAX1800v2 root=31:10 mtdparts=spi32766.0:768k(0:SBL1),64k(0:MIBIB),1664k(0:QSEE),64k(0:DEVCFG),128k(0:RPM),64k(0:CDT),64k(0:APPSBLENV),640k(0:APPSBL),256k(0:ART),28672k(inactive),28672k(inactive2),64k(custom),64k(0:KEYS),2304k(0:WIFIFW)'
tftpboot <filename-of-initramfs-kernel>.bin && bootm
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This will allow the AP to send radius requests via the websocket
to the gateway for routing to the correct AAA.
Fixes: WIFI-7328
Signed-off-by: John Crispin <john@phrozen.org>
Changes made in OpenWrt supported targets to Include Indio's UM-325AC AP which is an indoor WiFi5 AP based on ipq4019 chipset.
Signed-off-by: Sohail Ahmad <sohail@indionetworks.com>
Because we have an another similar device named gl-axt1800,
so we put the common functions in a dtsi file. And we'll
submit a PR for gl-axt1800 soon.
Hardware:
* SoC: Qcom IPQ6000
* RAM: DDR3L 512MB
* Flash: 128MB Nand
* Ethernet: 5x GbE
* WLAN: 2x2 2.4GHz 600Mbps + 2x2 5GHz 1200Mbps (builtin + builtin)
* LEDS: 1x white, 1x blue
* Buttons: 1x switch, 1x reset
* USB: 1x 3.0(Type-A)
* Power: 12VDC, 1.5A
Installation:
* from qsdk to openwifi:
upgrade "openwrt-ipq807x-glinet_ax1800-squashfs-nand-factory.bin" via web ui
without keep config.
* upgrade "openwrt-ipq807x-glinet_ax1800-squashfs-sysupgrade.tar" if you are already in openwifi.
Signed-off-by: Jianhui Zhao <jianhui.zhao@gl-inet.com>
