We've been declaring a bunch of statically-sized arrays:
extern struct foo_t foo[FOO_COUNT];
And then initializing them like so:
struct foo_t foo[FOO_COUNT] = {
/* blah */
};
That only catches cases where we initialize with too many entries. It
doesn't catch cases where we haven't initialized enough. This change tests
for both cases like so:
extern struct foo_t foo[];
struct foo_t foo[] = {
/* blah */
};
BUILD_ASSERT(ARRAY_SIZE(foo) == FOO_COUNT);
The affected arrays are:
adc_channels[ADC_CH_COUNT]
gpio_list[GPIO_COUNT]
temp_sensors[TEMP_SENSOR_COUNT]
x86_signal_list[X86_SIGNAL_COUNT]
i2c_ports[I2C_PORTS_USED]
BUG=chrome-os-partner:18343
BRANCH=falco,peppy
TEST=build all platforms
All platforms should still build, all tests should still pass.
Change-Id: Ibb16dc3201f32df7cdc875648e89ba4ffb09f733
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63833
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Rename onewire_led to led_driver_ds2413, since we may have other LED
drivers hanging off a one-wire bus in the future.
No functional changes, just renaming config options.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms
Change-Id: I1d70b1c5778da94bda4ebef3b57f7c39bfba2322
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63273
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
CONFIG_FMAP is now defined by default, because all platforms other
than the host unit tests use it.
No functional changes, just renaming config options and removing dead code.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms
Change-Id: Ie6496310c822491068e2fa6976933486f26badb0
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63271
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
If we are hibernating indefinitely, just exit with hibernate exit code.
If hibernating with a delay, delay for that amount of time and then
reboot.
BUG=chrome-os-partner:19235
TEST='hibernate 1' and see emulator reboot after a second with reset
flag 'hibernate'
BRANCH=None
Change-Id: If25bf2eefbcf275f2592b92a997a9d7e1ff2384d
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62970
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
With this, the emulator is able to reboot itself without the help of
run_host_test script. This makes it easier for development and also
speeds up the test.
BUG=chrome-os-partner:19235
TEST=Pass all tests
BRANCH=None
Change-Id: Ifa510442de19256c671ab91b6bc75fe9e8b9dc7b
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62969
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
To create a token by concatenating already-defined macros and new
text, it's necessary to use multiple levels of macro. We'd already
done that in several places in the code such as STM32_CAT; this now
standardizes it into a single place.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=Build all platforms; examine ec.RO.map to see that irq_*_handler and prio_* symbols
evaluated the same as before. (Other macro evaluations would simply fail to compile
if they were incorrect, since the concatenated tokens wouldn't fully expand.)
Change-Id: Ic9bf11d27881a84507fe7b6096dab6217c6c6dc7
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63231
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The preliminary bolt support allows the board to boot
with all the necessary peripherals working except for the
following things:
- Not all board temp sensors are added.
- WLAN is not powered on because of inrush issues.
- USB power chargers are fixed to normal mode for now.
BUG=chrome-os-partner:20372
BRANCH=None
TEST=Built and booted
Change-Id: Iea7a39e812bb396e5731f212630b7fe97c164bf2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62210
Reviewed-by: Randall Spangler <rspangler@chromium.org>
No functional changes, just renaming config options.
Remove README, now that all options described in it have been moved to
config.h, and the remaining information is out of date. (Yes, we
should have a README which describes the organization of the EC
repository, but that's a matter for another CL; this one's about
cleaning up config options.)
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms
Change-Id: Iafefbe94369f1217c698f11d358bc0ecac2bdfde
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63145
Reviewed-by: Vic Yang <victoryang@chromium.org>
All of these were defined on all but a few platforms, and those
explicitly #undef them. So define them as enabled by default in
config.h so the board.h files are cleaner.
No functional changes; just rearranging/renaming config constants.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms; FEATURES=test emerge-falco chromeos-ec
Change-Id: I1201a1472ae29641e9e219c2a0347691ca64cd28
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63102
Reviewed-by: Vic Yang <victoryang@chromium.org>
Reset flags should be set properly according to reset type. Also, on
system jump, current time should be preserved.
BUG=chrome-os-partner:19235
TEST='sysjump rw' and check time is the same.
TEST='reboot hard' and see '[Reset cause: hard]'
BRANCH=None
Change-Id: I00fd2c652d10c237f23cc6a33e0b667422bc625d
Signed-off-by: Vic Yang <victoryang@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62958
Reviewed-by: Randall Spangler <rspangler@chromium.org>
These are now described in config.h. The various BQ chargers now also
use a consistent naming for their sense resistor options.
No functional changes, just renaming, and removal of obsolete
never-defined configs.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms
Change-Id: Ie274546fe45f5ffc6fd0f26096c4622805baf8a0
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62540
This adds two new fields: the ideal write size for best EC flashing
performance (e.g., page mode instead of word mode), and a flags field
with a flag to indicate whether the EC erases its bits to 0 or 1.
The EC still supports the old version 0 command, since u-boot and
flashrom expect that to work.
BUG=chrome-os-partner:20973
BRANCH=(all haswell); this will speed up flashing and software sync
TEST=ectool flashinfo
1. old EC, new ectool -> only reports version 0 info
2. new EC, old ectool -> only reports version 0 info
3. new EC, new ectool -> reports new fields
Change-Id: I484327fe22a58d2b69d7f6ac767b2d3e81b3e0b7
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62378
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The curent code ends up creating a veneer for interrupt_enable/disable()
which isn't really needed (see below). By calling the interrupt code while
still running from flash we can avoid this.
I cannot see any problem with the current implementation, but it seems that
with this patch I also avoid an exception.
BUG=chrome-os-partner:20976
BRANCH=none
TEST=manual
Build EC and see code generated like this:
200029ec <iram_flash_write>:
200029ec: b538 push {r3, r4, r5, lr}
200029ee: 460d mov r5, r1
200029f0: 4604 mov r4, r0
200029f2: f000 f83d bl 20002a70 <__interrupt_disable_veneer>
...
20002a4a: f000 b809 b.w 20002a60 <__interrupt_enable_veneer>
20002a4e: bf00 nop
20002a60 <__interrupt_enable_veneer>:
20002a60: b401 push {r0}
20002a62: 4802 ldr r0, [pc, #8] ; (20002a6c <__interrupt_enable_veneer+0xc>)
20002a64: 4684 mov ip, r0
20002a66: bc01 pop {r0}
20002a68: 4760 bx ip
20002a6a: bf00 nop
20002a6c: 080007f5 .word 0x080007f5
20002a70 <__interrupt_disable_veneer>:
20002a70: b401 push {r0}
20002a72: 4802 ldr r0, [pc, #8] ; (20002a7c <__interrupt_disable_veneer+0xc>)
20002a74: 4684 mov ip, r0
20002a76: bc01 pop {r0}
20002a78: 4760 bx ip
20002a7a: bf00 nop
20002a7c: 080007f1 .word 0x080007f1
With this patch the veneers go away.
Change-Id: Idfe173b4c8d45a142914b2388bcff8ba708c657c
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62243
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
There's nothing LM4-specific about the switch module; it's just
checking GPIOs and updating a memory-mapped register.
No code changes; just moving a file.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=verify switch.c is compiled for link and falco, but not pit or spring
Change-Id: I186f3aac1405c7ba8d94b47bb2586c2ad191daba
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61930
Power button logic is common across all platforms and is not
LM4-specific, so move it to its own module. Switch.c will eventually
be moving to common/ and will common across all platforms (not just
x86), and splitting out the x86 power button logic is needed before
that too.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=manual
1) power on system with both lid and power button.
2) power+refresh -> reboots
3) power+refresh+esc -> recovery mode
4) power+refresh+downarrow -> reboots, AP stays off
5) toggling recovery GPIO via servo should generate SW debug output
showing bit 0x10 toggling
Change-Id: I07714e2c035dceece66f90407983397d2697e7d5
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61780
The configure_kblight_gpios() funciton was specific to
the link board. Therefore, move the function to be defined
within the board-specific file.
BUG=chrome-os-partner:20372
BRANCH=None
TEST=Built. Tested similar change on bolt.
Change-Id: Ib5847130450024c50d6526d2c1a64d67ab501637
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62209
This file will soon contain the exhaustive list of all CONFIG defines
and their descriptions.
Chip-level configs are renamed to config_chip.h to avoid naming
conflicts.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms
Change-Id: I9e94146f5b4c016894bd3ae3d371c4b9f3f69afe
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62122
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Both of these are included via common.h, which is in turn included by
most other header files. Directly including board.h or config.h is
redundant and discouraged.
No code changes, just removing #includes.
This is in preparation for making a top-level config.h file, but that
change will be easier to review if it doesn't touch as many files.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms
Change-Id: I204bcebe5607c6e6808821eb071cfc31d2a93a7c
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62121
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Chipset control of wireless power uses the new API instead of overriding
the wireless power itself.
Refactor board-specific support for it to just a few config #defines
instead of board-specific functions. This makes some assumptions
about the polarity of the enable signals. Not making those
assumptions would require defining an array of structs or some other
heavier-weight board-specific info. Since the assumptions hold for
all current boards, let's make them now because this is a step in the
right direction, and reserve doing something more general until we
actually have a use case for it (so we build in just the flexibility
we need).
BUG=chrome-os-partner:18343
BRANCH=none
TEST=build all platforms; see that link wifi turns on at boot and off at
shutdown (verify via 'gpioget' from EC console)
Change-Id: Ic036e76158198d2d5e3dd244c3c7b9b1e8d62982
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61608
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
This code is not LM4-specific, it's x86-specific. So it doesn't
belong in chip/lm4. Put it in its own module rather than leaving it
in switch.c, since some x86 systems may need the power button state
machine but not the backlight-enable passthru.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=Quickly run a magnet over the lid switch; the backlight goes off and then
back on.
Change-Id: I72f7139b73f91539dcfbe6b5cb6d56587ab66fde
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61595
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
This moves most of the code into a common module, leaving only the
board-specific GPIOs (now listed in a struct in board.c) and the
chipset-specific state machine with multiple copies.
BUG=chrome-os-partner:18343
BRANCH=none
TEST=boot link; verify suspend and resume work; shut back down and see
it go to G3 after 10 sec.
Change-Id: Iafa8ba55a4870bb0119ff4161a1a9054fcc7955f
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60949
The AC adapter detection isn't measuring the expected values, most likely
because we're not providing enough current for the ADC circuitry to sample.
This tells the ADC to take 64 samples for every reading and average them
together. That seems to fix it.
BUG=chrome-os-partner:19594
BRANCH=none
TEST=manual
To test, use a scope to probe the voltage pin 6 of the AC adapter connector.
Compare that with the measured result from the ADC, by using the EC
console's "adc" command.
Before this change:
Adapter Probed(mV) ADC(mV) error
45W 469 415 11.5%
65W 600 530 11.6%
90W 794 701 11.7%
After this change:
Adapter Probed(mV) ADC(mV) error
45W 469 452 3.6%
65W 600 590 1.6%
90W 794 773 2.6%
Close enough.
Change-Id: I5ab5526934a5a2711969a90a26631d54c7863da7
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61346
Reviewed-by: Randall Spangler <rspangler@chromium.org>
It previously relied on the switch module to enable/disable the
keyboard backlight when the lid changed position. It can do that itself now.
BUG=chrome-os-partner:20743
BRANCH=none
TEST=Boot link in a dark room where the keyboard backlight is on. Briefly run
a magnet over the lid switch and see the keyboard backlight blink off and
then back on.
Change-Id: Iadf02b780a4990db25b6f0b3e1e0692f49c5488d
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61194
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Instead of #if defined(BOARD_foo) for all new boards, flip around the
No functional changes, just rearranging code.
BUG=chrome-os-partner:20529
BRANCH=none
TEST=keyboard LED still blinks in suspend on pit
Change-Id: I185d642a5f412c8b4b0d16e62373c6b2bba71b0f
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61108
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
STM32L erases flash to 0, not 1, so we need a config value to indicate
that. This speeds up flash erase on STM32L by not re-erasing
already-erased blocks.
BUG=chrome-os-partner:13066
BRANCH=none
TEST=manual - hack flash_physical_erase() to print something just after
flash_is_erased() check.
1. flasherase 0x1f800 0x800
2. flashwrite 0x1fa00 0x100
3. flasherase 0x1f800 0x800 -> only re-erases 0x1fa00
Change-Id: I4d726caf0605e7815b9360bb2d44bdfdd757b4a2
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61110
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Flash writes must be done from 32-bit-aligned source buffers. Force
the protcol buffer to be aligned like we do for the lpc interface.
BUG=chrome-os-partner:20571
BRANCH=none
TEST=ectool flashread 0x1f800 0x800 /tmp/foo
ectool flasherase 0x1f800 0x800
ectool flashwrite 0x1f800 /tmp/foo
Change-Id: Icaa3259bcbc36be49345da5e19ad8a0790b73923
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60892
These constants are scattered around the various interface
implementations and should be in one place. This will also clean up
the u-boot side when ec_commands.h is copied there.
BUG=chrome-os-partner:20257
BRANCH=none
TEST=build link, spring, pit; test 'ectool hello'
Change-Id: Ib1425db00ec8220538d8c5c65107ac9548009516
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60810
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
As different boards can use the same EC but use different
pins for the same functionality it is required to properly
abstract out the bank and pin used for the one wire interface.
Provide this ability.
BUG=chrome-os-partner:20372
BRANCH=None
TEST=built for failure and success on link
Change-Id: Ie20f2319d9cd6f5ec63b4178ecebc45a90a51042
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60798
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This is necessary to support larger packet sizes for host protocol
ver.3. The host previously didn't have any way to know how big a
packet the EC could accept / respond with (except on LPC, where the
size is determined by the I/O window).
BUG=chrome-os-partner:20257
BRANCH=none
TEST='ectool protoinfo' returns good info; on link,
Protocol info:
protocol versions: 2 3
max request: 256 bytes
max response: 256 bytes
flags: 0x00000000
and on pit,
Protocol info:
protocol versions: 2 3
max request: 544 bytes
max response: 544 bytes
flags: 0x00000001
Change-Id: Ic1e3831d9b4a96ffbf365c0d09b6023472de39a9
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60703
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
No functional changes, just cleanup.
BUG=chrome-os-partner:20529
BRANCH=none
TEST='waitms 2000' reboots the system with a watchdog reset cause
Change-Id: I8fcee92476a287e6cb81bf9012f29c87d2aca0ba
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60680
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Previously, code which needed to work on all STM32F platforms needed
to specify them by name (CHIP_VARIANT_stm32f100 ||
CHIP_VARIANT_stm32f10x), and we needed extra symlinks in the
chip/stm32/ directory to allow the build system to find
family-specific files.
Add a CHIP_FAMILY level of abstraction, so that things which are
common across all STM32F platforms don't need to specify every STM32F
variant. Make the chip build look for family-specific filenames
instead of variant-specific filenames (except for config*.h, which is
actually variant specific).
In the few places where things actually are variant-specific, keep
using the existing CHIP_VARIANT defines.
Code refactoring only; no functional changes.
BUG=chrome-os-partner:20567
BRANCH=none
TEST=build all platforms
Change-Id: I1da831aadabf8b8dd9dfde423cac13c9f43eb953
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60247
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Vic Yang <victoryang@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bitfields are now in registers.h where they belong.
BUG=chrome-os-partner:20529
BRANCH=none
TEST='crosec test' from u-boot still works
Change-Id: I726550a32b61111c906c1b10c628c5e47eff74fb
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60179
Bitfields are now in registers.h where they belong.
BUG=chrome-os-partner:20529
BRANCH=none
TEST='crosec test' from u-boot still works
Change-Id: If0d79a66a90665c8ea336a006d76ccbc00a927ec
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60139
Reviewed-by: Vic Yang <victoryang@chromium.org>
When TOT link moved to 128KB images, I missed two references to 80KB.
Fix those, so TOT now builds 128KB images for all lm4-based platforms.
BUG=chromium:252584
BRANCH=none (link branch will stay at 80KB images)
TEST=sysjump rw doesn't crash
Change-Id: I5f25cf97ec706374d03ce8ecff6572c1c84242b5
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60153
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The maximum packet length for LPC is limited by the I/O space window
size. But that's not the case for SPI or LPC. Rename LPC constant
before adding a SPI constant.
BUG=chrome-os-partner:20257
BRANCH=none
TEST=build link
Change-Id: I088327a11eff18d401c773db953700a36f9c1bb4
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59959
Explicitly use enum for dma_channel, instead of ints (since channel is
1-based in the docs and 0-based in the enum). Add enum values for
other channels like USART.
Use volatile structs instead of typecasting through REG32().
Other assorted code cleanup.
Remove DMA2 partial support, since neither STM32F100R8 nor STM32L151x
has hardware support for it and it cluttered the code.
No functional changes.
BUG=chrome-os-partner:20485
BRANCH=none
TEST=from pit root shell, 'ectool version' still works
Change-Id: Ifdd62fb287c608a684ba8fa16934dfcab83ee609
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59949
Power LED PWM now uses the same functions as the hardware timer.
BUG=chrome-os-partner:20414
BRANCH=none
TEST=Suspend system. Power button LED pulses smoothly still.
Change-Id: Ib5ca6655d815462baaf68600ad14c4c0c680a6af
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59838
Automatically drop the clock speed to 1 MHz MSI, then disable HSI and
move to lower-power flash mode. This cuts power from 2400uA to 150uA.
Note that at 1 MHz, we drop received characters on the UART if you
type too fast (or copy/paste, or use arrow keys). Clock speed can be
manually overridden back to 16 MHz via 'clock hsi'.
BUG=chrome-os-partner:20414
BRANCH=none
TEST=with AP on, 'clock' reports 16 MHz.
with AP off, 'clock' reports 1 MHz.
Change-Id: I070c80db0aa5f3a98a7bad6050890bcc2fe008d6
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59832
Modules which care about system clock frequency now hook HOOK_FREQ_CHANGE.
- hwtimer
- i2c
- uart (which is now also smart enough to use x8 oversampling instead of
x16 when the system clock is too slow to support x16)
Added 'clock' debug command to set system clock frequency.
STM32F platforms don't change clock frequency; on those platforms,
clock_get_freq() simply returns CPU_CLOCK, so behavior of those
platforms is unchanged.
BUG=chrome-os-partner:20414
BRANCH=none
TEST=from EC console:
- reboot ap-off -> to make sure AP is off during testing
- clock msi2 -> reports 2MHz clock
- battery -> reports battery info
- clock msi1 -> reports 1MHz clock
- battery -> reports battery info
- clock hsi -> reports 16MHz clock
- battery -> reports battery info
- power on -> AP powers on and host commands succeed
Change-Id: Ib8276bf124727e4fb502297ca8b3d6d4b6170241
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59645
Clean up timer initialization code to be more general, so that we can
use timer 9 for the LSB on STM32L. Then use timer 4 for the watchdog
helper.
BUG=chrome-os-partner:18781
BRANCH=none
TEST=From EC console:
timerinfo -> current time still counts up properly
waitms 2000 -> prints watchdog info before rebooting
Change-Id: Ib0ba496b0eadb93756dcd1841857546910baf2a9
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59612
Reviewed-by: Simon Glass <sjg@chromium.org>
This fixes the problem where the EC consumes too much power during suspend.
BUG=chrome-os-partner:20223
BRANCH=none
TEST=from root shell, 'powerd_suspend'. 1.8V_MICOM should not go up.
after resume, 'ectool hello' should still work.
Change-Id: I93b781e96bea633419e923a83f1f6d7300ae8c54
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59474
Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
