This change sets the initial power button state to init-on
if the power button is pressed.
BUG=b:37274183
BRANCH=none
TEST=Enter recovery mode by power+recovery button press.
Change-Id: I6ed849bc303e7cdbcb975ae2a6ff278093c86088
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/486946
Reviewed-by: Duncan Laurie <dlaurie@google.com>
We need to process the stop condition after slaver receiver is executed,
or else we will lost the last byte of the transmission.
BRANCH=none
BUG=b:38510075
TEST=`make BOARD=rose -j`, AP suspend/resume should complete within 3 secs
Change-Id: I6390a908b6c05b875b8bb2c0a124292785110b20
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://chromium-review.googlesource.com/512463
Commit-Ready: Wei-Ning Huang <wnhuang@chromium.org>
Tested-by: Wei-Ning Huang <wnhuang@chromium.org>
Reviewed-by: Rong Chang <rongchang@chromium.org>
Allow to configure the sensor to detect autonomously finger touch event
similar to what is done in the suspend() routine of the kernel fpc1020
driver.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=b:35648259
TEST=make BOARD=eve_fp
Change-Id: I8b78bd6bdeecd8658850383417c950d9025fdf40
Reviewed-on: https://chromium-review.googlesource.com/491072
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Move the existing fingerprint host command in the driver and
add more of them to prepare the new fingerprint architecture.
The commands are mostly stubbed for now.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
CQ-DEPEND=*364728
BRANCH=none
BUG=b:35648259
TEST=make BOARD=eve_fp (with and without a private repository)
do a fingerprint image capture with 'fptest'.
Change-Id: Ie17a5fde2d6470c6272e8059bddc845cea07aff2
Reviewed-on: https://chromium-review.googlesource.com/491071
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Typically, we do not need RW section to be able to update rollback
information (rollback block should be protected when RW is running),
so we can save some flash space by undefining this option.
BRANCH=none
BUG=b:35586219
TEST=make newsizes saves ~420 bytes on hammer and staff.
Change-Id: Ic457673e56ace083f2ebb1ca0f37f54bf125bfa4
Reviewed-on: https://chromium-review.googlesource.com/511983
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
We want to always be able to update cr50 image to a newer version,
even if the AP is not cooperating.
BRANCH=cr50
BUG=b:35580805
TEST=verified that update of a prod image is possible
Change-Id: I3bbe2c4aca8bf0c3129f4495db0e76405a2ed189
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/511285
Reviewed-by: Nick Sanders <nsanders@chromium.org>
This is copied chip/g version as of commit 0e5497db6, plus the following
uncommited usb_update patch (CL:458469):
a0176a1cc usb_updater: Flush all data from endpoint before trying to update
On top of that, a good number of common-code specific modifications are
added: new extra commands, new first_response_pdu format, use of FMAP.
BRANCH=none
BUG=b:35587170
TEST=usb_updater binary identical before and after this change.
TEST=make BOARD=hammer -j && \
( cd extra/usb_updater && make && \
time sudo ./usb_updater2 ../../build/hammer/ec.bin )
TEST=cd extra/usb_updater; make
# Jump to RW
sudo ./usb_updater2 -j
sleep 0.5
# Update RO, then reboot
sudo ./usb_updater2 ../../build/hammer/ec.bin
sleep 0.5
# Update RW (first tell RO to not jump to RW)
sudo ./usb_updater2 -s
sudo ./usb_updater2 ../../build/hammer/ec.bin
TEST=cd extra/usb_updater; make
# Tell RW to jump back to RO
sudo ./usb_updater2 -w
sleep 0.5
# Update RW, then reboot
sudo ./usb_updater2 -s
sudo ./usb_updater2 ../../build/hammer/ec.bin
TEST=usb_updater2 can update hammer, and read its version, rollback
version and key version.
Change-Id: I09da894d83e2b4d6c2e46cab301522c27fa0160c
Reviewed-on: https://chromium-review.googlesource.com/458468
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Nick Sanders <nsanders@chromium.org>
In old system driver, ec clears "Predefined Time Occurred" (PTO) flag
before setting a new alarm (PT field in WTC). If PT field is the same
as the first 25 TTC bits at this moment, we might receive unexpected
rtc interrupt again. This CL sets new alarm first then clears PTO flag
to make sure rtc interrupt is issued from new alarm.
BRANCH=none
BUG=b:38310685
TEST=Duplicated the same symptom by the script in issue 38310685 on
gru. No symptoms occurred with the same script for 3 hours by applying
this CL.
Change-Id: Ia6410d6aa4ef8e2acb7bfadf9192d619045bfa58
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/508572
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Make the dcrypto ecdsa verify code check that r,s are in range, and
not depend on the caller C code to have done so.
For instance, s equal to 0 would result in infinite loop during
computation of its modular inverse.
BRANCH=none
BUG=b:35587381
TEST=TCG tests pass
Change-Id: I13f7811be030aed9feaa11c45dc68d4bfd08fb76
Reviewed-on: https://chromium-review.googlesource.com/508819
Commit-Ready: Marius Schilder <mschilder@chromium.org>
Tested-by: Marius Schilder <mschilder@chromium.org>
Reviewed-by: Marius Schilder <mschilder@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Adds min_frequency and max_frequency to struct motion_sensor_t.
New attributes min_frequency and max_frequency are now returned in
ectool's MOTIONSENSE_CMD_INFO response.
Incremented ectool's MOTIONSENSE_CMD_INFO version to version 3.
Add constants for MIN_FREQUENCY and MAX_FREQUENCY to each sensor's
header file.
BRANCH=none
BUG=chromium:615059
TEST=build/boot and verify MOTIONSENSE_CMD_INFO response on kevin,
make buildall -j passes.
Change-Id: I66db9715c122ef6bb4665ad5d086a9ecc9c7c93a
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/482703
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Gru ran out of room with upcoming change, disabled CONFIG_CMD_ALS
to free up the needed space and keep build from breaking.
BRANCH=none
BUG=chromium:615059
TEST=verified gru target build doesn't run out of flash space using
"make buildall -j"
Change-Id: Ifb76ad0fe4693dfa4415370354c6d5af2bd4cc11
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/490846
Reviewed-by: Scott Collyer <scollyer@chromium.org>
The first two versions of servo_v4 (red and blue) have the TPD2E001
ESD between VBUS and CC1/CC2. This part has a breakdown min voltage of
11V. Therefore for these versions of servo_v4, need to limit VBUS to
less than the default 20V value.
This CL adds support to read two board ID gpios attached to the gpio
expansion part. The max VBUS voltage is limited to 9V for red/blue and
allowed to be 20V for black.
BUG=b:38351574
BRANCH=servo_v4
TEST=Manual
Modified a servo_v4 to add the 2 new pullup resistors. Tested with
this unit and with a unit that does not have the pullups. Verified
that without the pullups the version ID reads a 0 and the max VBUS
voltage that will be requested by the CHG port is 9V. Wih the modified
servo_v4, verified that the version reads 3 and the CHG port will
request up to 20V.
Change-Id: Ic41fcbe3a5c000282552c7322b5ab18ebb203cd2
Signed-off-by: Scott Collyer <scollyer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/507027
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Nick Sanders <nsanders@chromium.org>
This change adds CONFIG_POWER_BUTTON_INIT_IDLE. When it's set,
the system starts with the power button state idle. It means
when the board boots from power-off, it stays at G3.
BUG=b:37536389
BRANCH=none
TEST=Power on Fizz. Verify it stays at G3. Verify it boots
by pressing power button.
Change-Id: I09a62a69d9f201b2dc261838cc9b4425fe3a8dc1
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/486945
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Instead of using EC hibernate shut down the PMIC over I2C.
This will turn off the DSW rail and the EC completely. The existing
wake sources are still able to wake the system.
BUG=b:35647896
BRANCH=none
TEST=manual testing on Eve board to ensure that wake sources that
are expected to wake from G3 are still functional. (AC, power, lid)
Change-Id: I91b14ec360190176dba0a8e7c458b2b0ab5b6dcd
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://chromium-review.googlesource.com/506719
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Enable the mutable scancode sets for EVT boards and reassign the
existing F13 scancode to instead send the new 0[e0 58] 1[e0 07]
scancode instead.
BUG=b:36735408
BRANCH=none
TEST=manual testing on Eve EVT to ensure that the key that used
to send F13 now sends the new scancode. Also test on P1 to ensure
that the key still sends F13.
Change-Id: Ia134db7b069d5bf10c931ee7ce66dd1ea85d3544
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://chromium-review.googlesource.com/506718
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Add an option to allow the scancode sets to be mutable. The only
reason to use this is to allow a scancode to be changed at runtime,
for instance to support different keyboards in one image.
The side effect of this is the scancode sets are moved out of the
shared RO section.
BUG=b:36735408
BRANCH=none
TEST=make -j buildall
Change-Id: Iefb97691d1f295411d7b5db603d9214d41af49fd
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://chromium-review.googlesource.com/506717
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
First, libpayload expects the keyboard interface index to be 0.
Then, hid_iface_request needs to reply to USB_HID_DT_HID request
with the content of struct usb_hid_descriptor. With current code,
the variable name is generated (and therefore hard to guess), so
we create a new set of macros so that we can use a specific
variable name.
Also, add support for HID Get_Protocol and Set_Protocol, as they
are compulsory for devices supporting boot protocol, even though
those are mostly no-op for now.
Finally, add a note regarding USB HID keyboard boot protocol, to
make sure that we do not accidentally change the report format.
BRANCH=none
BUG=b:36538963
TEST=Keyboard works in FW screen, both trackpad and keyboard
still work when AP has booted.
TEST=hammer/staff can still be updated (both RO from RW, and RW
from RO)
Change-Id: Ibea4888385909c9ce3b430464e5805c039d4b9ed
Reviewed-on: https://chromium-review.googlesource.com/505796
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
This applies the simple rule: Charging port led is on, other
is off. When charging, LED is amber, otherwise it's white.
Open questions:
- Do we want blinking on low battery? On which side(s)? In
which AP states?
- No blinking in S3? That's ok?
- Need to add led blinking support for special debug mode
- Recovery mode blinking does not work as LED is powered from
a rail that is not on when AP is in S5.
BRANCH=none
BUG=b:37970194
TEST=Charge from one side, led is first amber, then white when
battery is full. Switch side, led behaves the same way.
Change-Id: I0531d72cd621148c0d0cce57a32b7310792d9936
Reviewed-on: https://chromium-review.googlesource.com/497372
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add the evaluation board driver of npcx7 series ec for testing. If you
received the evb which ec is 128-pins package, please notice it has
the following limitations.
a. No GPIOD7/E0 pins.
b. No I2C4_0, I2C4_1, I2C5_1 and I2C6_1 ports.
c. No ADC7, ADC8 and ADC9 channels.
d. No JTAG port 1.
e. Do not enable CONFIG_HIBERNATE_PSL since no PSL circuit on evb.
This CL also includes:
1. Modified reset config from srst to sysresetreq in openocd/npcx.cfg.
Make sure openocd driver can reset ec by using NVIC_SYSRESETREQ.
2. Add flash utilities for npcx7 ec in openocd/npcx_cmds.tcl.
3. Add npcx7_evb support in flash_ec.
BRANCH=none
BUG=none
TEST=Passed all npcx7 drivers verification on the evb no matter which
ec's package is 128 or 144 pins package.
Change-Id: I8224d97cd66ce483d70816f47b2e124308f1b69c
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/505832
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Some chip supports two owned slave address. The second slave address is
used for other purpose such as board specific i2c commands. This option
can be set if user of the second slave address requires larger host
packet er size.
BRANCH=none
BUG=b:37187312
TEST=`make BOARD=rose -j`
Change-Id: I8d0b04bf4dded55e3957c7b25d849663299593e5
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://chromium-review.googlesource.com/472288
Commit-Ready: Wei-Ning Huang <wnhuang@chromium.org>
Tested-by: Wei-Ning Huang <wnhuang@chromium.org>
Reviewed-by: Rong Chang <rongchang@chromium.org>
This patch clones I2C slave and hostcmd driver from stm32f0.
This patch contains contribution from Wei-Ning Huang <wnhuang@chromium.org>
for fixing i2c slave transmitter (CL:471726).
BUG=chromium:688979
TEST=build and load on dev board, run i2cget/set on host and check
return value.
BRANCH=none
Change-Id: I3d159d5bdd4bda6c229cf6d275ab4982836628dc
Signed-off-by: Rong Chang <rongchang@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/461037
Tested-by: Wei-Ning Huang <wnhuang@chromium.org>
Reviewed-by: Wei-Ning Huang <wnhuang@chromium.org>
dabc580d7e "poppy: Add ARC++ sensor support." accidentally moved pin
from gpio 36 to 30. When updating gpio.inc for rev1, I accidentally
thought the pinout had been changed. Let's fix this.
BRANCH=none
BUG=none
TEST=Boot on poppy and soraka
Change-Id: I6f44acdcfa7bc8f21144b26887eda503a350a6b0
Reviewed-on: https://chromium-review.googlesource.com/497232
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
When AP boots and FW screen is shown (e.g. in developer mode),
AP FW is querying MKBP status in a loop, leading to a lot of "+"
being printed in the EC console.
To avoid this issue, let's print "(++)" after a command is received
5 times in a row.
BRANCH=none
BUG=b:37925684
TEST=Set GBB flags to 0x4a38, reasonable number of "+" is printed
on EC console on boot, which firmware screen is being shown.
Change-Id: I8368c558b97e7a2513b979322bd4bba442626b27
Reviewed-on: https://chromium-review.googlesource.com/505948
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
At init time, read resolution/dpi from trackpad, and check that
logical/physical dimensions match the expected values, provided
at build-time.
BRANCH=none
BUG=b:38277869
TEST=Flash staff, no error message at boot time. Flash hammer image
onto staff, a warning is shown at boot time.
Change-Id: I5ef7d25b6e6525c2bd6fc023f58f3a242134d962
Reviewed-on: https://chromium-review.googlesource.com/505857
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In principle, trackpad dimensions (logical and physical), can be
probed from the trackpad at runtime, but this would slow down setup
time, as we need to wait for the trackpad to be initialized to read
those. Also, we do not have a framework to generate HID report
at runtime, and a new base with new trackpad would probably require
a new overlay anyway.
Also, set appropriate (temporary) values for both hammer and staff.
BRANCH=none
BUG=b:38277869
TEST=Connect hammer/staff to host, correct logical dimensions are
shown in evtest, and resolution is always 32.
Change-Id: I39b84274d71ca2f4e285f3324c0841331aae9bc1
Reviewed-on: https://chromium-review.googlesource.com/505856
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Fizz has two power sources: barrel jack and type-c port. It
selects a power source at boot and does not dynamicall switch
to the other ports after that.
Fizz initializes all power suppliers of all ports to zero then
initialize the source supplier (barrel jack or type-c port).
When both sources are provided, it prefers a barrel jack. This
detection is done by reading the voltage on PPVAR_PWR_IN.
If barrel jack is detected as a sink, type-c port works as a
source only. If type-c port is detected as a sink, type-c
port works as a sink only.
Fizz does not have a battery. So, battery module is removed.
BUG=b:37573548,b:37316498
BRANCH=none
TEST=Boot on both type-c & barrel jack.
Change-Id: If4f5ff0c6019d06ac9dacb5dd365f5aa96bffef3
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/499547
Add the new scan codes for the updated keyboard matrix:
R0,C3 = Search (in addition to existing location at R1,C0)
R0,C5 = New key using code 0[e0 58] and 1[e0 07]
There are no changes to existing scan codes.
BUG=b:36735408
BRANCH=none
TEST=make -j buildall
Change-Id: Ieba22eacd21a5c2dde3c7c43eb62b767fc0db42e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://chromium-review.googlesource.com/506716
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
The assert in the charge state machine when there is no battery and no AC
is causing a lot of headaches during development, and I don't believe it
adds any value to panic the EC like this as it prevents the system from
coming up and any debug from happening. This is especially bad with H1
locking out any useful debug by preventing flashing the EC.
On Eve EVT we have some 'bad' batteries that are not correctly asserting
presence pin, and when powering with adapter this this check happens before
AC_PRESENT asserts because the USB PD negotiation is still happening so the
EC gets stuck in a reboot loop.
Similarly we had issues with the Krill board in the Whale BFT station that
was triggering the same assert.
In both cases there is an underlying hardware issue which is being
investigated separately, but it is impossible to debug these systems
because the EC will not come up.
With this assert removed the EC and AP can boot and the LED blinks red to
indicate there is battery a problem and the OS also reports a problem that
the battery cannot be found, and we are able to do further debug without
having to open the case. Additionally the error message is printed every
~second and it is very obvious from the EC console that there is a problem.
Similar issues were reported at various points on Glados, Chell, Kevin,
Elm, and Reef.
BUG=b:35563537
BRANCH=none
TEST=successfully boot and debug a failing Eve system
Change-Id: I002b26d54428d29192a7097f1aae18f3223c5707
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://chromium-review.googlesource.com/477733
Reviewed-by: Scott Collyer <scollyer@chromium.org>
Cr50 holds the EC in reset when it wants to flash the EC or AP. This
will trigger a pulse on the tpm reset signal. In early Cr50 versions
when the tpm was reset we would reboot cr50, so we added some code to
prevent cr50 from resetting itself when the update was going on.
sys_rst_asserted would check if there was an update going on and ignore
the signal if update in progress was true. At the end of the update the
deferred function was used to reset Cr50 after the update was complete.
None of this is needed anymore. We can just release the EC from reset at
the end of the update. This change removes usb_spi_update_in_progress
and the deferred update_finished.
BUG=b:35571516
BRANCH=none
TEST=flash the bob ec and ap using ccd.
Change-Id: I79416dba178c06bbc7289ad96968ee4e61947c4c
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/506571
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
There many TODOs sprinkled in the code, some of them have been
addressed or do not apply any mode. This patch removes them.
BRANCH=cr50
BUG=none
TEST=built and ran cr50 on reef
Change-Id: Ica6edb204e5cc0cc9dc7f0d43fd39e7ddaf56809
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/506496
Reviewed-by: Randall Spangler <rspangler@chromium.org>
hammer corresponds to poppy, and staff corresponds to soraka.
Current differences (hammer/staff):
- USB id (5022/502b)
- PWM frequency (10kHz/100Hz):
- On staff, driving PWM at 10kHz leads to an actual duty cycle
around 30-40%, with a PWM output at 1% (long rise/fall time).
100Hz looks better, we get ~1.45% duty with 1% PWM output.
BRANCH=none
BUG=b:38277869
TEST=Flash staff, boots fine.
TEST=pwm 0 1 shows quite dim backlight on staff.
Change-Id: I66ba2adf89fbee8578ee473afb28e3e242b4d111
Reviewed-on: https://chromium-review.googlesource.com/505855
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In a lab servo, flash_ec is executed without the board flag. In this
case, don't check the board flag for raiden and simply respect the
raiden flag.
BRANCH=none
BUG=b:38319398
TEST=Ran the flash_ec script in a lab servo.
Change-Id: Ib3757a4b7b550fd77facffdf2009cc3317591888
Reviewed-on: https://chromium-review.googlesource.com/506461
Commit-Ready: Wai-Hong Tam <waihong@google.com>
Tested-by: Wai-Hong Tam <waihong@google.com>
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
always_memset() implements a version of memset
that survives compiler optimization. This change
replaces instances of the (placeholder) call
dcrypto_memset() with always_memset().
Also add a couple of missing memsets and
fix related TODOs by replacing memset()
with always_memset().
BRANCH=none
BUG=none
TEST=TCG tests pass
Change-Id: I742393852ed5be9f74048eea7244af7be027dd0e
Signed-off-by: nagendra modadugu <ngm@google.com>
Reviewed-on: https://chromium-review.googlesource.com/501368
Commit-Ready: Nagendra Modadugu <ngm@google.com>
Tested-by: Nagendra Modadugu <ngm@google.com>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Andrey Pronin <apronin@chromium.org>
We don't have an external pull-up on WP_L, so let's use an internal
one instead.
BRANCH=none
BUG=b:35582031
TEST=gpioget WP_L shows 1 as default value, servo can control
value, and when servo is not driving the pin, value goes back
to 1.
Change-Id: I75148cde9ab89c1dfb05f3182608894a3e1390fa
Reviewed-on: https://chromium-review.googlesource.com/502849
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
In order to support write-protect mechanism for the internal flash
of npcx7 ec, WP_IF, bit 5 of DEV_CTL4, is used to achieve this by
controlling the WP_L pin of internal flash. During ec initialization
or any utilities related to access status registers, we'll protect them
if WP_L is active. Please notice the type of WP_IF is R/W1S. It means we
only can unlock write protection of internal flash by rebooting ec.
This CL also includes:
1. Add protect_range array of npcx7's internal flash (W25Q80) for
write-protect mechanism.
2. Add bypass of bit 7 of DEVCNT.
BRANCH=none
BUG=none
TEST=No build errors for all boards using npcx5 series. (Besides gru)
Build poppy board and upload FW to platform. No issues found.
Passed flash write-protect checking on npcx796f evb.
Change-Id: I0e669ce8b6eaebd85e062c6751e1f3dd809e21e2
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/501727
Reviewed-by: Randall Spangler <rspangler@chromium.org>
When cr50 detects recovery button (not keyboard) combo:
recovery+power, volume-up+down+power, etc., it should
(ideally) hard-reset the EC.
This patch allows power-on reset in addition to reset-pin reset
to enter recovery mode when recovery button combo is pressed.
BUG=b:35585326
BRANCH=none
TEST=make buildall. Tested on Poppy.
Change-Id: I15aeef99d21ddc774441ead56fba56d459595cc9
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/503573
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This patch adds code to control the power LED.
BUG=b:37646390
BRANCH=none
TEST=Verify LED turns green, red, amber, off. Verify LED turns green
or off when chipset is on or off, respectively.
Change-Id: I1d7940d9bb4414d97c541ead802efeb8f279533e
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/486947
