ipq807x_v5.4/ipq50xx: When device is booting, it causes lan/wan ports bridge together

Fixes: WIFI-14849
Signed-off-by: jackcybertan <jack.tsai@cybertan.com.tw>

feeds/ipq807x_v5.4/ath11k-wifi/Makefile

@@ -49,6 +49,7 @@ ALLWIFIBOARDS:= \
 	indio-um-510axm-v1 \
 	indio-um-325ax-v2 \
 	indio-um-335ax \
+	indio-um-345ax \
 	indio-um-525axp \
 	indio-um-525axm \
 	muxi-ap3220l \
@@ -447,6 +448,7 @@ $(eval $(call generate-ath11k-wifi-package,indio-um-510axp-v1,Indio UM-510AXP V1
 $(eval $(call generate-ath11k-wifi-package,indio-um-510axm-v1,Indio UM-510AXM V1))
 $(eval $(call generate-ath11k-wifi-package,indio-um-325ax-v2,Indio UM-325AX V2))
 $(eval $(call generate-ath11k-wifi-package,indio-um-335ax,Indio UM-335AX))
+$(eval $(call generate-ath11k-wifi-package,indio-um-345ax,Indio UM-345AX))
 $(eval $(call generate-ath11k-wifi-package,indio-um-525axp,Indio UM-525AXP))
 $(eval $(call generate-ath11k-wifi-package,indio-um-525axm,Indio UM-525AXM))
 $(eval $(call generate-ath11k-wifi-package,sonicfi-rap630c-311g,Sonicfi RAP630C 311G))

feeds/ipq807x_v5.4/ipq50xx/Makefile

@@ -27,6 +27,7 @@ DEFAULT_PACKAGES += kmod-qca-nss-dp kmod-qca-ssdk swconfig \
 	kmod-ath11k-ahb  ath11k-firmware-ipq5018 \
 	kmod-gpio-button-hotplug iwinfo \
 	qca-ssdk-shell kmod-bootconfig \
-	uboot-envtools -procd-ujail
+	uboot-envtools -procd-ujail \
+	kmod-mdio-qca
 
 $(eval $(call BuildTarget))

feeds/ipq807x_v5.4/ipq50xx/config-5.4

@@ -635,7 +635,7 @@ CONFIG_MDIO_BITBANG=y
 CONFIG_MDIO_BOARDINFO=y
 # CONFIG_MDIO_BUS_MUX_MULTIPLEXER is not set
 CONFIG_MDIO_GPIO=y
-CONFIG_MDIO_QCA=y
+CONFIG_MDIO_QCA=m
 # CONFIG_MDM_GCC_9615 is not set
 # CONFIG_MDM_LCC_9615 is not set
 # CONFIG_MEMORY_HOTPLUG is not set

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-eww631-b1.dts

@@ -391,8 +391,8 @@
 				mdio-bus = <&mdio1>;
 				reset_gpio = <&tlmm 0x26 0>;
 				switch_cpu_bmp = <0x40>;  /* cpu port bitmap (Port 6 GMAC) */
-				switch_lan_bmp = <0x3c>; /* lan port bitmap */
-				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				switch_lan_bmp = <0x1c>; /* lan port bitmap */
+				switch_wan_bmp = <0x20>;  /* wan port bitmap */
 				qca,ar8327-initvals = <
 						0x00004 0x7600000   /* PAD0_MODE */
 						0x00008 0x1000000   /* PAD5_MODE */

feeds/ipq807x_v5.4/ipq50xx/files/arch/arm64/boot/dts/qcom/qcom-ipq5018-rap630w-311g.dts

@@ -408,8 +408,8 @@
 				mdio-bus = <&mdio1>;
 				reset_gpio = <&tlmm 0x26 0>;
 				switch_cpu_bmp = <0x40>;  /* cpu port bitmap (Port 6 GMAC) */
-				switch_lan_bmp = <0x3c>; /* lan port bitmap */
-				switch_wan_bmp = <0x0>;  /* wan port bitmap */
+				switch_lan_bmp = <0x1c>; /* lan port bitmap */
+				switch_wan_bmp = <0x20>;  /* wan port bitmap */
 				qca,ar8327-initvals = <
 						0x00004 0x7600000   /* PAD0_MODE */
 						0x00008 0x1000000   /* PAD5_MODE */

feeds/ipq807x_v5.4/ipq50xx/modules.mk

@@ -242,3 +242,17 @@ define KernelPackage/bootconfig/description
 endef
 
 $(eval $(call KernelPackage,bootconfig))
+
+define KernelPackage/mdio-qca
+  SUBMENU:=$(NETWORK_DEVICES_MENU)
+  TITLE:=Model for MDIO to QCA PHY connection
+  KCONFIG:=CONFIG_MDIO_QCA
+  FILES:=$(LINUX_DIR)/drivers/net/phy/mdio-qca.ko
+  AUTOLOAD:=$(call AutoLoad,30,mdio-qca)
+endef
+
+define KernelPackage/mdio-qca/description
+ This driver supports the MDIO interface found in Qualcomm Atheros ipq Soc chip.
+endef
+
+$(eval $(call KernelPackage,mdio-qca))

feeds/ipq807x_v5.4/ipq60xx/base-files/etc/board.d/02_network

@@ -20,6 +20,7 @@ qcom_setup_interfaces()
 		ucidef_set_interface_wan "eth0 eth1"
 		ucidef_set_interface_lan ""
 		;;
+	indio,um-310ax-v1|\
 	yuncore,ax840)
 		ucidef_set_interface_lan "eth0"
 		ucidef_set_interface_wan "eth1"
@@ -79,6 +80,7 @@ qcom_setup_macs()
 	emplus,wap386v2)
 		wan_mac=$(cat /sys/class/net/eth0/address)
 		;;
+	indio,um-310ax-v1|\
 	yuncore,ax840)
 		wan_mac=$(cat /sys/class/net/eth1/address)
 		lan_mac=$(macaddr_add "$wan_mac" 1)

feeds/ipq807x_v5.4/ipq60xx/base-files/etc/hotplug.d/firmware/10-ath11k-caldata

@@ -82,6 +82,7 @@ case "$FIRMWARE" in
 	hfcl,ion4x_2|\
 	hfcl,ion4x_3|\
 	hfcl,ion4xe|\
+	indio,um-310ax-v1|\
 	wallys,dr6018|\
 	wallys,dr6018-v4|\
 	yuncore,ax840|\

feeds/ipq807x_v5.4/ipq60xx/base-files/lib/upgrade/platform.sh

@@ -119,6 +119,7 @@ platform_check_image() {
 	cig,wf196|\
 	glinet,ax1800|\
 	glinet,axt1800|\
+	indio,um-310ax-v1|\
 	wallys,dr6018|\
 	wallys,dr6018-v4|\
 	edgecore,eap101|\
@@ -156,6 +157,7 @@ platform_do_upgrade() {
 		;;
 	glinet,ax1800|\
 	glinet,axt1800|\
+	indio,um-310ax-v1|\
 	wallys,dr6018|\
 	wallys,dr6018-v4|\
 	yuncore,ax840|\

feeds/ipq807x_v5.4/ipq60xx/files/arch/arm64/boot/dts/qcom/qcom-ipq6018-indio-um-310ax-v1.dts

@@ -0,0 +1,321 @@
+/dts-v1/;
+/*
+ * Copyright (c) 2019-2021, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "ipq6018.dtsi"
+#include "ipq6018-cpr-regulator.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "Indio UM-310AX V1";
+	compatible = "indio,um-310ax-v1", "qcom,ipq6018-cp03", "qcom,ipq6018";
+	interrupt-parent = <&intc>;
+	qcom,msm-id = <0x1A5 0x0>;
+
+	aliases {
+		/*
+		 * Aliases as required by u-boot
+		 * to patch MAC addresses
+		 */
+		ethernet0 = "/soc/dp2";
+		ethernet1 = "/soc/dp1";
+		led-boot = &led_system;
+		led-failsafe = &led_system;
+		led-running = &led_system;
+		led-upgrade = &led_system;
+	};
+
+	chosen {
+		bootargs = "console=ttyMSM0,115200,n8 rw init=/init";
+#ifdef __IPQ_MEM_PROFILE_256_MB__
+		bootargs-append = " swiotlb=1";
+#else
+		bootargs-append = " swiotlb=1 coherent_pool=2M";
+#endif
+	};
+
+	/*
+	 * +=========+==============+========================+
+	 * |        |              |                         |
+	 * | Region | Start Offset |          Size           |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * | Linux  |  0x41000000  |         139MB           |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * |        |              |                         |
+	 * +--------+--------------+-------------------------+
+	 * | TZ App |  0x49B00000  |           6MB           |
+	 * +--------+--------------+-------------------------+
+	 *
+	 * From the available 145 MB for Linux in the first 256 MB,
+	 * we are reserving 6 MB for TZAPP.
+	 *
+	 * Refer arch/arm64/boot/dts/qcom/qcom-ipq6018-memory.dtsi
+	 * for memory layout.
+	 */
+
+/* TZAPP is enabled only in default memory profile */
+#if !defined(__IPQ_MEM_PROFILE_256_MB__) && !defined(__IPQ_MEM_PROFILE_512_MB__)
+	reserved-memory {
+		tzapp:tzapp@49B00000 {	/* TZAPPS */
+			no-map;
+			reg = <0x0 0x49B00000 0x0 0x00600000>;
+		};
+	};
+#endif
+};
+
+&tlmm {
+	uart_pins: uart_pins {
+		mux {
+			pins = "gpio44", "gpio45";
+			function = "blsp2_uart";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	spi_0_pins: spi_0_pins {
+		mux {
+			pins = "gpio38", "gpio39", "gpio40", "gpio41";
+			function = "blsp0_spi";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	button_pins: button_pins {
+		wps_button {
+			pins = "gpio9";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_0 {
+			pins = "gpio64";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		mux_1 {
+			pins = "gpio65";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		mux_2 {
+			pins = "gpio75";
+			function = "gpio";
+			bias-pull-up;
+		};
+	};
+
+	leds_pins: leds_pins {
+		led_blue {
+			pins = "gpio35";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		led_green {
+			pins = "gpio37";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		led_red {
+			pins = "gpio32";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	button_pins: button_pins {
+		rst_button {
+			pins = "gpio19";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+};
+
+&soc {
+	mdio@90000 {
+		pinctrl-0 = <&mdio_pins>;
+		pinctrl-names = "default";
+		phy-reset-gpio = <&tlmm 75 0>;
+		status = "ok";
+		phy0: ethernet-phy@0 {
+			reg = <3>;
+		};
+		phy1: ethernet-phy@1 {
+			reg = <4>;
+		};
+	};
+
+	ess-switch@3a000000 {
+		switch_cpu_bmp =   <0x01>; /* cpu port bitmap */
+		switch_lan_bmp =   <0x10>; /* lan port bitmap */
+		switch_wan_bmp =   <0x20>; /* wan port bitmap */
+		switch_inner_bmp = <0x80>; /*inner port bitmap*/
+		switch_mac_mode =  <0x00>; /* mac mode for uniphy instance0*/
+		switch_mac_mode1 = <0xff>; /* mac mode for uniphy instance1*/
+		switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
+
+		qcom,port_phyinfo {
+			port@3 {
+				port_id = <0x04>;
+				phy_address = <0x03>;
+			};
+
+			port@4 {
+				port_id = <0x05>;
+				phy_address = <0x04>;
+			};
+		};
+	};
+
+	dp1 {
+		device_type = "network";
+		compatible = "qcom,nss-dp";
+		qcom,id = <0x04>;
+		reg = <0x3a001600 0x200>;
+		qcom,mactype = <0x00>;
+		local-mac-address = [00 00 00 00 00 00];
+		qcom,link-poll = <0x01>;
+		qcom,phy-mdio-addr = <0x03>;
+		phy-mode = "sgmii";
+	};
+
+	dp2 {
+		device_type = "network";
+		compatible = "qcom,nss-dp";
+		qcom,id = <0x05>;
+		reg = <0x3a001800 0x200>;
+		qcom,mactype = <0x00>;
+		local-mac-address = [00 00 00 00 00 00];
+		qcom,link-poll = <0x01>;
+		qcom,phy-mdio-addr = <0x04>;
+		phy-mode = "sgmii";
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 19 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led_system: system {
+			label = "ax860:green:system";
+			gpio = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g {
+			label = "ax860:blue:wlan2g";
+			gpio = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g {
+			label = "ax860:red:wlan5g";
+			gpio = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	pinctrl-0 = <&uart_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&spi_0 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	cs-select = <0>;
+	status = "ok";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		compatible = "n25q128a11";
+		linux,modalias = "m25p80", "n25q128a11";
+		spi-max-frequency = <50000000>;
+		use-default-sizes;
+	};
+};
+
+&qpic_bam {
+	status = "ok";
+};
+
+&qpic_nand {
+	status = "ok";
+
+	nand@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+	};
+};
+
+&ssphy_0 {
+	status = "ok";
+};
+
+&qusb_phy_0 {
+	status = "ok";
+};
+
+&usb3 {
+	status = "ok";
+};
+
+&nss_crypto {
+	status = "ok";
+};

feeds/ipq807x_v5.4/ipq60xx/image/ipq60xx.mk

@@ -92,7 +92,7 @@ define Device/indio_um-310ax-v1
   SUPPORTED_DEVICES := indio,um-310ax-v1
   DEVICE_PACKAGES := ath11k-wifi-indio-um-310ax-v1 uboot-env
 endef
-#TARGET_DEVICES += indio_um-310ax-v1
+TARGET_DEVICES += indio_um-310ax-v1
 
 define Device/indio_um-510axp-v1
   DEVICE_TITLE := Indio UM-510AXP V1

feeds/ipq807x_v5.4/ipq807x/base-files/etc/board.d/01_leds

@@ -14,7 +14,8 @@ cig,wf194c4)
 	;;
 edgecore,eap102|\
 edgecore,oap102|\
-edgecore,oap103)
+edgecore,oap103|\
+indio,um-345ax)
 	ucidef_set_led_netdev "poe" "poe" "green:wan" "eth0"
         ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wifi5" "phy0tpt"
         ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wifi2" "phy1tpt"

feeds/ipq807x_v5.4/ipq807x/base-files/etc/board.d/02_network

@@ -18,7 +18,8 @@ qcom_setup_interfaces()
 		ucidef_set_interface_wan "eth0"
 		ucidef_set_interface_lan ""
 		;;
-	cig,wf194c4)
+	cig,wf194c4|\
+	indio,um-345ax)
 		ucidef_set_interface_lan "eth0"
 		ucidef_set_interface_wan "eth1"
 		;;

feeds/ipq807x_v5.4/ipq807x/base-files/etc/hotplug.d/firmware/10-ath11k-caldata

@@ -73,6 +73,7 @@ case "$FIRMWARE" in
 	edgecore,oap103 |\
 	edgecore,eap106 |\
 	emplus,wap380c|\
+	indio,um-345ax|\
 	qcom,ipq807x-hk01|\
 	qcom,ipq807x-hk14|\
 	tplink,ex227|\
@@ -107,7 +108,8 @@ ath11k-macs)
 	edgecore,eap102|\
 	edgecore,oap102|\
 	edgecore,oap103|\
-	edgecore,eap106)
+	edgecore,eap106|\
+	indio,um-345ax)
 		ath11k_generate_macs
 		;;
 	cig,wf196)

feeds/ipq807x_v5.4/ipq807x/base-files/lib/upgrade/platform.sh

@@ -30,6 +30,7 @@ platform_check_image() {
 	edgecore,oap103|\
 	edgecore,eap106|\
 	emplus,wap380c|\
+	indio,um-345ax|\
 	sonicfi,rap650c|\
 	tplink,ex227|\
 	tplink,ex447)
@@ -61,7 +62,8 @@ platform_do_upgrade() {
 	tplink,ex447)
 		nand_upgrade_tar "$1"
 		;;
-	edgecore,eap106)
+	edgecore,eap106|\
+	indio,um-345ax)
 		CI_UBIPART="rootfs1"
 		[ "$(find_mtd_chardev rootfs)" ] && CI_UBIPART="rootfs"
 		nand_upgrade_tar "$1"

feeds/ipq807x_v5.4/ipq807x/files/arch/arm64/boot/dts/qcom/qcom-ipq807x-indio-um-345ax.dts

@@ -0,0 +1,713 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2020 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2025, Shubham Vishwakarma <shubhamvis98@fossfrog.in>
+ */
+
+/dts-v1/;
+
+#include "ipq8074.dtsi"
+#include "ipq8074-ac-cpu.dtsi"
+
+/ {
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	model = "Indio UM-345AX";
+	compatible = "indio,um-345ax", "qcom,ipq807x-hk09", "qcom,ipq807x";
+	qcom,msm-id = <0x178 0x0>;
+	interrupt-parent = <&intc>;
+
+	aliases {
+		serial0 = &blsp1_uart5;
+		/* Aliases as required by u-boot to patch MAC addresses */
+		ethernet1 = "/soc/dp5";
+		ethernet0 = "/soc/dp6";
+
+		led-boot = &led_red;
+		led-failsafe = &led_red;
+		led-running = &led_green;
+		led-upgrade = &led_green;
+		led-gateway = &led_blue;
+		led-factory = &led_blue;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	soc {
+		pinctrl@1000000 {
+			pinctrl-0 = <&mcu_rst &mcu_rsv &usb_rear_pwr &usb_side_pwr &usb_hub_rst>;
+			pinctrl-names = "default";
+
+			mcu_rst: mcu_rst_pins {
+				pins = "gpio54";
+				function = "gpio";
+				drive-strength = <8>;
+				bias-disable;
+				output-low;
+			};
+
+			mcu_rsv: mcu_rsv_pins {
+				pins = "gpio56";
+				function = "gpio";
+				drive-strength = <8>;
+				bias-disable;
+			};
+
+			usb_rear_pwr: usb_rear_pwr_pins {
+				pins = "gpio29";
+				function = "gpio";
+				drive-strength = <8>;
+				bias-disable;
+				output-high;
+			};
+
+			usb_side_pwr: usb_side_pwr_pins {
+				pins = "gpio30";
+				function = "gpio";
+				drive-strength = <8>;
+				bias-disable;
+				output-high;
+			};
+
+			usb_hub_rst: usb_hub_rst_pins {
+				pins = "gpio55";
+				function = "gpio";
+				drive-strength = <8>;
+				bias-disable;
+				output-high;
+			};
+
+			button_pins: button_pins {
+				reset_button {
+					pins = "gpio57";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+			};
+
+			mdio_pins: mdio_pinmux {
+				mux_0 {
+					pins = "gpio68";
+					function = "mdc";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+				mux_1 {
+					pins = "gpio69";
+					function = "mdio";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+				mux_2 {
+					pins = "gpio25";
+					function = "gpio";
+					bias-pull-up;
+				};
+				mux_3 {
+					pins = "gpio44";
+					function = "gpio";
+					bias-pull-up;
+				};
+			};
+			led_pins: led_pins {
+				led_red {
+					pins = "gpio0";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-pull-down;
+				};
+
+				led_2g {
+					pins = "gpio2";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-pull-down;
+				};
+
+				led_5g {
+					pins = "gpio9";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-pull-down;
+				};
+			};
+		};
+
+		serial@78b3000 {
+			status = "ok";
+		};
+
+		spi@78b5000 {
+			status = "ok";
+			pinctrl-0 = <&spi_0_pins>;
+			pinctrl-names = "default";
+			cs-select = <0>;
+
+			m25p80@0 {
+				  compatible = "n25q128a11";
+				  #address-cells = <1>;
+				  #size-cells = <1>;
+				  reg = <0>;
+				  spi-max-frequency = <50000000>;
+			};
+		};
+
+		dma@7984000 {
+			 status = "ok";
+		};
+
+		nand@79b0000 {
+			status = "ok";
+
+			nand@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				nand-ecc-strength = <4>;
+				nand-ecc-step-size = <512>;
+				nand-bus-width = <8>;
+			};
+		};
+
+		qusb@79000 {
+			status = "ok";
+		};
+
+		ssphy@78000 {
+			status = "ok";
+		};
+
+		usb3@8A00000 {
+			status = "ok";
+		};
+
+		usb3@8C00000 {
+			status = "ok";
+		};
+
+		qusb@59000 {
+			status = "ok";
+		};
+
+		ssphy@58000 {
+			status = "ok";
+		};
+
+		usb3@8C00000 {
+			status = "ok";
+		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			pinctrl-0 = <&button_pins>;
+			pinctrl-names = "default";
+			status = "ok";
+
+			button@1 {
+				label = "reset";
+				linux,code = <KEY_RESTART>;
+				gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
+				linux,input-type = <1>;
+				debounce-interval = <60>;
+			};
+		};
+
+		mdio: mdio@90000 {
+			pinctrl-0 = <&mdio_pins>;
+			pinctrl-names = "default";
+			phy-reset-gpio = <&tlmm 37 0 &tlmm 25 1 &tlmm 44 1>;
+			phy0: ethernet-phy@0 {
+				reg = <0>;
+			};
+			phy1: ethernet-phy@1 {
+				reg = <1>;
+			};
+			phy2: ethernet-phy@2 {
+				reg = <2>;
+			};
+			phy3: ethernet-phy@3 {
+				reg = <3>;
+			};
+			phy4: ethernet-phy@4 {
+				reg = <24>;
+			};
+			phy5: ethernet-phy@5 {
+				reg = <28>;
+			};
+		};
+
+		ess-switch@3a000000 {
+			switch_cpu_bmp = <0x1>;  /* cpu port bitmap */
+			switch_lan_bmp = <0x3e>; /* lan port bitmap */
+			switch_wan_bmp = <0x40>; /* wan port bitmap */
+			switch_mac_mode = <0x0>; /* mac mode for uniphy instance0*/
+			switch_mac_mode1 = <0xf>; /* mac mode for uniphy instance1*/
+			switch_mac_mode2 = <0xf>; /* mac mode for uniphy instance2*/
+			bm_tick_mode = <0>; /* bm tick mode */
+			tm_tick_mode = <0>; /* tm tick mode */
+			qcom,port_phyinfo {
+				port@0 {
+					port_id = <1>;
+					phy_address = <0>;
+				};
+				port@1 {
+					port_id = <2>;
+					phy_address = <1>;
+				};
+				port@2 {
+					port_id = <3>;
+					phy_address = <2>;
+				};
+				port@3 {
+					port_id = <4>;
+					phy_address = <3>;
+				};
+				port@4 {
+					port_id = <5>;
+					phy_address = <24>;
+					port_mac_sel = "QGMAC_PORT";
+				};
+				port@5 {
+					port_id = <6>;
+					phy_address = <28>;
+					port_mac_sel = "QGMAC_PORT";
+				};
+			};
+			port_scheduler_resource {
+				port@0 {
+					port_id = <0>;
+					ucast_queue = <0 143>;
+					mcast_queue = <256 271>;
+					l0sp = <0 35>;
+					l0cdrr = <0 47>;
+					l0edrr = <0 47>;
+					l1cdrr = <0 7>;
+					l1edrr = <0 7>;
+				};
+				port@1 {
+					port_id = <1>;
+					ucast_queue = <144 159>;
+					mcast_queue = <272 275>;
+					l0sp = <36 39>;
+					l0cdrr = <48 63>;
+					l0edrr = <48 63>;
+					l1cdrr = <8 11>;
+					l1edrr = <8 11>;
+				};
+				port@2 {
+					port_id = <2>;
+					ucast_queue = <160 175>;
+					mcast_queue = <276 279>;
+					l0sp = <40 43>;
+					l0cdrr = <64 79>;
+					l0edrr = <64 79>;
+					l1cdrr = <12 15>;
+					l1edrr = <12 15>;
+				};
+				port@3 {
+					port_id = <3>;
+					ucast_queue = <176 191>;
+					mcast_queue = <280 283>;
+					l0sp = <44 47>;
+					l0cdrr = <80 95>;
+					l0edrr = <80 95>;
+					l1cdrr = <16 19>;
+					l1edrr = <16 19>;
+				};
+				port@4 {
+					port_id = <4>;
+					ucast_queue = <192 207>;
+					mcast_queue = <284 287>;
+					l0sp = <48 51>;
+					l0cdrr = <96 111>;
+					l0edrr = <96 111>;
+					l1cdrr = <20 23>;
+					l1edrr = <20 23>;
+				};
+				port@5 {
+					port_id = <5>;
+					ucast_queue = <208 223>;
+					mcast_queue = <288 291>;
+					l0sp = <52 55>;
+					l0cdrr = <112 127>;
+					l0edrr = <112 127>;
+					l1cdrr = <24 27>;
+					l1edrr = <24 27>;
+				};
+				port@6 {
+					port_id = <6>;
+					ucast_queue = <224 239>;
+					mcast_queue = <292 295>;
+					l0sp = <56 59>;
+					l0cdrr = <128 143>;
+					l0edrr = <128 143>;
+					l1cdrr = <28 31>;
+					l1edrr = <28 31>;
+				};
+				port@7 {
+					port_id = <7>;
+					ucast_queue = <240 255>;
+					mcast_queue = <296 299>;
+					l0sp = <60 63>;
+					l0cdrr = <144 159>;
+					l0edrr = <144 159>;
+					l1cdrr = <32 35>;
+					l1edrr = <32 35>;
+				};
+			};
+			port_scheduler_config {
+				port@0 {
+					port_id = <0>;
+					l1scheduler {
+						group@0 {
+							sp = <0 1>; /*L0 SPs*/
+							/*cpri cdrr epri edrr*/
+							cfg = <0 0 0 0>;
+						};
+					};
+					l0scheduler {
+						group@0 {
+							/*unicast queues*/
+							ucast_queue = <0 4 8>;
+							/*multicast queues*/
+							mcast_queue = <256 260>;
+							/*sp cpri cdrr epri edrr*/
+							cfg = <0 0 0 0 0>;
+						};
+						group@1 {
+							ucast_queue = <1 5 9>;
+							mcast_queue = <257 261>;
+							cfg = <0 1 1 1 1>;
+						};
+						group@2 {
+							ucast_queue = <2 6 10>;
+							mcast_queue = <258 262>;
+							cfg = <0 2 2 2 2>;
+						};
+						group@3 {
+							ucast_queue = <3 7 11>;
+							mcast_queue = <259 263>;
+							cfg = <0 3 3 3 3>;
+						};
+					};
+				};
+				port@1 {
+					port_id = <1>;
+					l1scheduler {
+						group@0 {
+							sp = <36>;
+							cfg = <0 8 0 8>;
+						};
+						group@1 {
+							sp = <37>;
+							cfg = <1 9 1 9>;
+						};
+					};
+					l0scheduler {
+						group@0 {
+							ucast_queue = <144>;
+							ucast_loop_pri = <16>;
+							mcast_queue = <272>;
+							mcast_loop_pri = <4>;
+							cfg = <36 0 48 0 48>;
+						};
+					};
+				};
+				port@2 {
+					port_id = <2>;
+					l1scheduler {
+						group@0 {
+							sp = <40>;
+							cfg = <0 12 0 12>;
+						};
+						group@1 {
+							sp = <41>;
+							cfg = <1 13 1 13>;
+						};
+					};
+					l0scheduler {
+						group@0 {
+							ucast_queue = <160>;
+							ucast_loop_pri = <16>;
+							mcast_queue = <276>;
+							mcast_loop_pri = <4>;
+							cfg = <40 0 64 0 64>;
+						};
+					};
+				};
+				port@3 {
+					port_id = <3>;
+					l1scheduler {
+						group@0 {
+							sp = <44>;
+							cfg = <0 16 0 16>;
+						};
+						group@1 {
+							sp = <45>;
+							cfg = <1 17 1 17>;
+						};
+					};
+					l0scheduler {
+						group@0 {
+							ucast_queue = <176>;
+							ucast_loop_pri = <16>;
+							mcast_queue = <280>;
+							mcast_loop_pri = <4>;
+							cfg = <44 0 80 0 80>;
+						};
+					};
+				};
+				port@4 {
+					port_id = <4>;
+					l1scheduler {
+						group@0 {
+							sp = <48>;
+							cfg = <0 20 0 20>;
+						};
+						group@1 {
+							sp = <49>;
+							cfg = <1 21 1 21>;
+						};
+					};
+					l0scheduler {
+						group@0 {
+							ucast_queue = <192>;
+							ucast_loop_pri = <16>;
+							mcast_queue = <284>;
+							mcast_loop_pri = <4>;
+							cfg = <48 0 96 0 96>;
+						};
+					};
+				};
+				port@5 {
+					port_id = <5>;
+					l1scheduler {
+						group@0 {
+							sp = <52>;
+							cfg = <0 24 0 24>;
+						};
+						group@1 {
+							sp = <53>;
+							cfg = <1 25 1 25>;
+						};
+					};
+					l0scheduler {
+						group@0 {
+							ucast_queue = <208>;
+							ucast_loop_pri = <16>;
+							mcast_queue = <288>;
+							mcast_loop_pri = <4>;
+							cfg = <52 0 112 0 112>;
+						};
+					};
+				};
+				port@6 {
+					port_id = <6>;
+					l1scheduler {
+						group@0 {
+							sp = <56>;
+							cfg = <0 28 0 28>;
+						};
+						group@1 {
+							sp = <57>;
+							cfg = <1 29 1 29>;
+						};
+					};
+					l0scheduler {
+						group@0 {
+							ucast_queue = <224>;
+							ucast_loop_pri = <16>;
+							mcast_queue = <292>;
+							mcast_loop_pri = <4>;
+							cfg = <56 0 128 0 128>;
+						};
+					};
+				};
+				port@7 {
+					port_id = <7>;
+					l1scheduler {
+						group@0 {
+							sp = <60>;
+							cfg = <0 32 0 32>;
+						};
+						group@1 {
+							sp = <61>;
+							cfg = <1 33 1 33>;
+						};
+					};
+					l0scheduler {
+						group@0 {
+							ucast_queue = <240>;
+							ucast_loop_pri = <16>;
+							mcast_queue = <296>;
+							cfg = <60 0 144 0 144>;
+						};
+					};
+				};
+			};
+		};
+
+		dp6 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			qcom,id = <6>;
+			reg = <0x3a001800 0x200>;
+			qcom,mactype = <0>;
+			local-mac-address = [000000000000];
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <28>;
+			phy-mode = "sgmii";
+		};
+
+		dp5 {
+			device_type = "network";
+			compatible = "qcom,nss-dp";
+			qcom,id = <5>;
+			reg = <0x3a001a00 0x200>;
+			qcom,mactype = <0>;
+			local-mac-address = [000000000000];
+			qcom,link-poll = <1>;
+			qcom,phy-mdio-addr = <24>;
+			phy-mode = "sgmii";
+		};
+
+		leds {
+			compatible = "gpio-leds";
+			pinctrl-0 = <&led_pins>;
+			pinctrl-names = "default";
+
+			led_red: led_sys {
+				label = "led_sys";
+				gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+				linux,default-trigger = "led_pwr";
+			};
+
+			led_green: led_2g {
+				label = "led_2g";
+				gpio = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+
+			led_blue: led_5g {
+				label = "led_5g";
+				gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+		};
+		nss-macsec0 {
+			compatible = "qcom,nss-macsec";
+			phy_addr = <0x18>;
+			mdiobus = <&mdio>;
+		};
+		nss-macsec1 {
+			compatible = "qcom,nss-macsec";
+			phy_addr = <0x1c>;
+			mdiobus = <&mdio>;
+		};
+	};
+};
+
+&apc_cpr {
+	/* Same CPR configuration as OAK */
+	compatible = "qcom,cpr4-ipq817x-apss-regulator";
+
+	thread@0 {
+		apc_vreg: regulator {
+			regulator-min-microvolt = <1>;
+			regulator-max-microvolt = <2>;
+			qcom,cpr-fuse-corners = <2>;
+			qcom,cpr-corners = <3>;
+			qcom,cpr-speed-bin-corners = <3>;
+			qcom,cpr-corner-fmax-map = <1 3>;
+
+			qcom,cpr-voltage-ceiling =
+				<840000 904000 944000>;
+			qcom,cpr-voltage-floor =
+				<592000 648000 712000>;
+			qcom,corner-frequencies =
+				<1017600000 1382400000 1382400000>;
+
+			qcom,cpr-open-loop-voltage-fuse-adjustment-0 =
+				/* Speed bin 0; CPR rev 0..7 */
+				< 0      0>,
+				< 0      0>,
+				< 0      0>,
+				< 0      0>,
+				< 0      0>,
+				< 0      0>,
+				< 0      0>,
+				< 0      0>;
+
+			qcom,cpr-open-loop-voltage-fuse-adjustment-1 =
+				/* Speed bin 0; CPR rev 0..7 */
+				<     0      0>,
+				<     0      0>,
+				<     0      0>,
+				< 20000  26000>,
+				<     0      0>,
+				<     0      0>,
+				<     0      0>,
+				<     0      0>;
+
+			qcom,cpr-open-loop-voltage-fuse-adjustment-v2-0 =
+				/* Speed bin 0; CPR rev 0..7 */
+				<     0      0>,
+				<     0      0>,
+				<     0      0>,
+				<     0      0>,
+				<     0      0>,
+				<     0      0>,
+				<     0      0>,
+				<     0      0>;
+
+			qcom,cpr-open-loop-voltage-fuse-adjustment-v2-1 =
+				/* Speed bin 0; CPR rev 0..7 */
+				<     0      0>,
+				<     0   7000>,
+				<     0      0>,
+				<     0      0>,
+				<     0      0>,
+				<     0      0>,
+				<     0      0>,
+				<     0      0>;
+
+			qcom,cpr-floor-to-ceiling-max-range =
+				< 40000 40000 40000>,
+				< 40000 40000 40000>,
+				< 40000 40000 40000>,
+				< 40000 40000 40000>,
+				< 40000 40000 40000>,
+				< 40000 40000 40000>,
+				< 40000 40000 40000>,
+				< 40000 40000 40000>;
+		};
+	};
+};
+
+&npu_cpr {
+	status = "disabled";
+};
+
+&nss0 {
+        qcom,low-frequency = <187200000>;
+        qcom,mid-frequency = <748800000>;
+        qcom,max-frequency = <1497600000>;
+};
+
+&nss0 {
+	npu-supply = <&dummy_reg>;
+	mx-supply = <&dummy_reg>;
+};
+
+&wifi0 {
+	qcom,board_id = <0x92>;
+};
+
+&wifi1 {
+	qcom,board_id = <0x292>;
+};

feeds/ipq807x_v5.4/ipq807x/image/ipq807x.mk

@@ -66,6 +66,15 @@ define Device/emplus_wap380c
 endef
 TARGET_DEVICES += emplus_wap380c
 
+define Device/indio_um-345ax
+  DEVICE_TITLE := Indio UM-345AX
+  DEVICE_DTS := qcom-ipq807x-indio-um-345ax
+  DEVICE_DTS_CONFIG=config@hk09
+  SUPPORTED_DEVICES := indio,um-345ax
+  DEVICE_PACKAGES := ath11k-wifi-indio-um-345ax uboot-envtools
+endef
+TARGET_DEVICES += indio_um-345ax
+
 define Device/sonicfi_rap650c
   DEVICE_TITLE := SonicFi RAP650C
   DEVICE_DTS := qcom-ipq807x-rap650c

feeds/ucentral/ucentral-client/files/etc/ucentral/version.json

@@ -1,5 +1,5 @@
 {
 	"major": 4,
 	"minor": 1,
-	"patch": 0
+	"patch": 1
 }

feeds/ucentral/ucentral-event/files/ucentral-event

@@ -275,23 +275,27 @@ handlers = {
 	},
 
 	vlan_add: function(notify) {
-		let vlan_id = `${notify.data.vlan_id}`;
-		vlan_refcount[vlan_id] = (vlan_refcount[vlan_id] || 0) + 1;
-
-		if (vlan_refcount[vlan_id] > 1) {
-			return;
-		}
-
 		if (config.config.swconfig)
 			return handlers.vlan_add_swconfig(notify);
 
-		for (let wan in wan_ports) {
-			let msg = {
-				name: wan,
-				vlan: [ `${notify.data.vlan_id}:t` ]
-			};
-			ubus.call('network.interface.up_none', 'add_device', msg);
-			ubus.call('udevstats', 'add_device', { device: wan, vlan: +notify.data.vlan_id });
+		let vlan_id = `${notify.data.vlan_id}`;
+		vlan_refcount[vlan_id] = (vlan_refcount[vlan_id] || 0) + 1;
+
+		let parts = split(notify.data.ifname, '-v');
+		let is_wifi_iface = (length(parts) == 2 && wildcard(parts[0], 'wlan*'));
+
+		if (vlan_refcount[vlan_id] > 1 && !is_wifi_iface)
+			return;
+
+		if (vlan_refcount[vlan_id] == 1) {
+			for (let wan in wan_ports) {
+				let msg = {
+					name: wan,
+					vlan: [ `${notify.data.vlan_id}:t` ]
+				};
+				ubus.call('network.interface.up_none', 'add_device', msg);
+				ubus.call('udevstats', 'add_device', { device: wan, vlan: +notify.data.vlan_id });
+			}
 		}
 
 		let msg = {
@@ -304,16 +308,16 @@ handlers = {
 	},
 
 	vlan_remove: function(notify) {
+		if (config.config.swconfig)
+			return;
+
 		let vlan_id = `${notify.data.vlan_id}`;
 		vlan_refcount[vlan_id] = (vlan_refcount[vlan_id] || 1) - 1;
 
-		if (vlan_refcount[vlan_id] > 0) {
+		if (vlan_refcount[vlan_id] > 0)
 			return;
-		}
 		delete vlan_refcount[vlan_id];
 
-		if (config.config.swconfig)
-			return;
 		for (let wan in wan_ports) {
 			let msg = {
 				name: wan,

feeds/ucentral/ucentral-schema/Makefile

@@ -4,10 +4,10 @@ PKG_NAME:=ucentral-schema
 PKG_RELEASE:=1
 
 PKG_SOURCE_URL=https://github.com/Telecominfraproject/wlan-ucentral-schema.git
-PKG_MIRROR_HASH:=f72d2e5b01ecb7a488d50d860da63664d992e50c7e046fed866be6733bab3c1c
+PKG_MIRROR_HASH:=c0f43db0530a38eb424e81908ad47a14e1d4d8f8a86eb148e34f98187c79ba6b
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_DATE:=2025-09-29
-PKG_SOURCE_VERSION:=676e1550c53b7d48a54aa759f65d341168627c5e
+PKG_SOURCE_DATE:=2025-10-16
+PKG_SOURCE_VERSION:=dc9cad95641266a08de73aab85d931d992090159
 PKG_MAINTAINER:=John Crispin <john@phrozen.org>
 PKG_LICENSE:=BSD-3-Clause
 

feeds/ucentral/ucentral-schema/files/etc/ucentral/examples/multi-psk.json

@@ -1,17 +1,12 @@
 {
 	"uuid": 2,
 	"radios": [
-		{
-			"band": "6G",
-			"country": "CA",
-			"channel-mode": "HE",
-			"channel-width": 80
-		},
 		{
 			"band": "5G",
 			"country": "CA",
 			"channel-mode": "HE",
-			"channel-width": 80
+			"channel-width": 80,
+			"channel": 36
 		},
 		{
 			"band": "2G",
@@ -57,10 +52,7 @@
 							"key": "bbbbbbbb"
 						}
 					],
-					"roaming": {
-						"message-exchange": "ds",
-						"generate-psk": true
-					}
+					"roaming": true
 				}
 			]
 		},

profiles/cig_wf189.yml

@@ -17,4 +17,4 @@ packages:
   - sysstat
   - kmod-cig-poe-judgment
 diffconfig: |
-  CONFIG_KERNEL_IPQ_MEM_PROFILE=0 
+  CONFIG_KERNEL_IPQ_MEM_PROFILE=0

profiles/cig_wf189w.yml

@@ -16,4 +16,4 @@ packages:
   - sysstat
   - kmod-cig-poe-judgment
 diffconfig: |
-  CONFIG_KERNEL_IPQ_MEM_PROFILE=0 
+  CONFIG_KERNEL_IPQ_MEM_PROFILE=0

profiles/indio_um-310ax-v1.yml

@@ -0,0 +1,13 @@
+---
+profile: indio_um-310ax-v1
+target: ipq60xx
+subtarget: generic
+description: Build image for the Indio UM-310AX V1
+image: bin/targets/ipq60xx/generic/openwrt-ipq60xx-indio_um-310ax-v1-squashfs-sysupgrade.tar
+feeds:
+  - name: ipq807x
+    path: ../../feeds/ipq807x_v5.4
+include:
+  - ucentral-ap
+packages:
+  - ipq60xx

profiles/indio_um-345ax.yml

@@ -0,0 +1,15 @@
+---
+profile: indio_um-345ax
+target: ipq807x
+subtarget: generic
+description: Build image for the Indio UM-345AX
+image: bin/targets/ipq807x/generic/openwrt-ipq807x-indio_um-345ax-squashfs-sysupgrade.tar
+feeds:
+  - name: ipq807x
+    path: ../../feeds/ipq807x_v5.4
+include:
+  - ucentral-ap
+packages:
+  - ipq807x
+diffconfig: |
+  CONFIG_KERNEL_IPQ_MEM_PROFILE=0