add a new config flag to support active low power control signal
BUG=chrome-os-partner:53665
BRANCH=none
TEST=Use multimeter to check for voltage present on the WiFi slot.
Use gpioget to check GPIO state in S0 (on) and S5 (off).
Change-Id: Ibeca88d16f39eadd7f29589cd3cd15aeef0dd524
Signed-off-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/347085
Commit-Ready: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Kevin uses inverted polarity (low = enable 5V output), so add a new CONFIG
to support this.
BUG=chrome-os-partner:53777
BRANCH=None
TEST=Manual on Kevin. Enable USB charger tasks, verify that VBUS is
properly detected on no-battery case.
Change-Id: Ifb3e5fa9db1973d9826435712711f0cb0fd1d3a5
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/349260
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Previously CONFIG_USB_PD_TCPM_VBUS had two uses which were independent:
- When operating as a TCPC, it indicated that the VBUS level should be
tracked (through GPIO inputs) and sent to the external TCPM when
appropriate.
- When operating as a TCPM, it indicated that the VBUS level should be
obtained by querying the TCPC.
These two independent uses have been split into
CONFIG_USB_PD_TCPC_TRACK_VBUS and CONFIG_USB_PD_VBUS_DETECT_TCPC, which
sould be more clear.
In addition, CONFIG_USB_PD_VBUS_DETECT_* CONFIGs have been added for
other means of VBUS detection.
BUG=chromium:616580
BRANCH=None
TEST=Verify kevin continues to boot + charge.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I936821481d6577e17e3e9c61ff97c037574d6923
Reviewed-on: https://chromium-review.googlesource.com/348950
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
move PRECHARGE_TIMEOUT to config.h so that we can customize precharge time to
meet client's spec.
BUG=none
BRANCH=master
TEST=`make -j buildall`, precharge time is set to 300s in elm.
Change-Id: I5c3bf0d5c5240b9c087e6cdb7c6e97301efa9f84
Signed-off-by: Ryan Zhang <Ryan.Zhang@quantatw.com>
Reviewed-on: https://chromium-review.googlesource.com/348151
Reviewed-by: Shawn N <shawnn@chromium.org>
Port SHA and P256 code to depend on third_party/cryptoc.
Remove config options CONFIG_SHA1, and CONFIG_SHA256 as
these are provided by third_party/cryptoc.
Also remove unused config options CONFIG_SHA384, CONFIG_SHA512.
Crypto functions prefixed by dcrypto_ (declared in internal.h ),
DCRYPTO_ (declared in dcrypto.h) are implemented under
chip/g/dcrypto, and otherwise are implemented under third_party/cryptoc.
BRANCH=none
BUG=chrome-os-partner:43025,chrome-os-partner:47524,chrome-os-partner:53782
TEST=all tests in test/tpm_test/tpmtest.py pass
Change-Id: If7da02849aba9703573559370af5fae721d594fc
Signed-off-by: nagendra modadugu <ngm@google.com>
Reviewed-on: https://chromium-review.googlesource.com/340853
Commit-Ready: Nagendra Modadugu <ngm@google.com>
Tested-by: Nagendra Modadugu <ngm@google.com>
Reviewed-by: Nagendra Modadugu <ngm@google.com>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Initialize the charge suppliers after change manager is initialized,
otherwise charge supplier current & voltage values will be overwritten
to -1 by the charge manager ini function.
BUG=chrome-os-partner:53788
BRANCH=None
TEST=Observed there are no "CL: p(port) s(supplier) i-1 v-1" prints
on the EC console.
Change-Id: Id0212c502d5833c016ac79ee15d21304d6d7ceb2
Signed-off-by: Vijay Hiremath <vijay.p.hiremath@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/347896
Commit-Ready: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Tested-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
There are a couple of issues that cr50 has when it cannot know the state
of servo, the EC, and the AP. This change adds support so we can detect
when the AP or EC has been powered on and when servo has been connected.
It uses the UART RX signals to monitor the power state of the AP and EC.
The TX signals are used to monitor the state of servo.
BUG=chrome-os-partner:52056,chrome-os-partner:52322
BRANCH=none
TEST=verify device states are correct when the AP and EC are powered on
or off and when Servo is attached or detached
Change-Id: Id0a2281b65cb367ecc8d0ca2f9a576672318a5fb
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/344019
Used #define CONFIG_FLASH_NVMEM to have functions in
/board/tpm2/NVMem.c utlitize on chip Nvmem functions.
On chip NV Memory availability is tied to an internal nvmem
error state which itself only depends on finding at least one
valid partition.
Added nvmem_is_different and nvmem_move functions which were
needed to complete the tpm2 platform interface. In addition,
added unit tests to support these two new functions.
BUG=chrome-os-partner:44745
BRANCH=none
TEST=manual
make runtests TEST_LIST_HOST=nvmem and verify that all tests pass.
Tested with tcg_test utility to test reads/writes using the
command "build/test-tpm2/install/bin/compliance --ntpm
localhost:9883 --select CPCTPM_TC2_3_33_07_01".
Change-Id: I475fdd1331e28ede00f9b674c7bee1536fa9ea48
Signed-off-by: Scott <scollyer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/346236
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Full implementation of NvMem read, write, and commit functions.
Includes partition definitions, shared memory allocation, and
initialization function.
Includes a set of unit tests located in ec/test/nvmem.c which
verify functionality.
This module is required by Cr50, however this CL does not
include any Cr50 specific code.
BUG=chrome-os-partner:44745
BRANCH=none
TEST=manual
make runtests TEST_LIST_HOST=nvmem and verify that all tests pass
Change-Id: I515b094f2179dbcb75dd11ab5b14434caad37edd
Signed-off-by: Scott <scollyer@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/345632
Commit-Ready: Scott Collyer <scollyer@chromium.org>
Tested-by: Scott Collyer <scollyer@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
This change provides a console command for setting,
and loading a usb serial number from flash. This
feature adds CONFIG_USB_SERIALNO, and currently only
has a useful implementation when PSTATE is present.
BUG=chromium:571477
TEST=serialno set abcdef; serialno load; reboot
BRANCH=none
Change-Id: I3b24cfa2d52d54118bc3fd54b276e3d95412d245
Signed-off-by: Nick Sanders <nsanders@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/337359
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The console adc command prints adc values in the
order they appear in hardware, however they are lableled
in the order they are enumerated in board.h, which is not
necessarily the same.
This prints the correct name and value pairs, and removes
the adc_read_all_channels function which is not otherwise
used.
BUG=chromium:571476
BRANCH=None
TEST="adc" command associates correct values with names now.
Change-Id: I688641953d20082224b4120eaefe0d634ad4c74c
Signed-off-by: Nick Sanders <nsanders@google.com>
Reviewed-on: https://chromium-review.googlesource.com/340892
Commit-Ready: Nick Sanders <nsanders@chromium.org>
Tested-by: Nick Sanders <nsanders@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
BUG=chrome-os-partner:53729
BRANCH=None
TEST=Manual on gru. Verify .rodata.evtsrcs section is non-empty in
ec.RO.map. Verify that we're no longer spammed with HC 0x67 (due to
constantly asserted interrupt).
Change-Id: I57ad1ba7fbdd99dfab84341560aff094ce9bc5b6
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/347415
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Third party code includes standard system headers,
but may not have include paths configured for the
platform.
Remove the dependency between assert.h and
platform headers util.h, and panic.h.
BRANCH=none
BUG=chrome-os-partner:43025,chrome-os-partner:47524
TEST=make buildall succeeds
Change-Id: Ic8d4dc1944765d2f0f80782afa574d7b8e54eb0f
Signed-off-by: nagendra modadugu <ngm@google.com>
Reviewed-on: https://chromium-review.googlesource.com/347080
Commit-Ready: Nagendra Modadugu <ngm@google.com>
Tested-by: Nagendra Modadugu <ngm@google.com>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
This allows the AP to protect a I2C passthru bus. A board-specific
function then defines what I2C commands are allowed, so that we
can white/black list some addresses (e.g. I2C address allowing
PD chip FW updating).
BRANCH=none
BUG=chrome-os-partner:52431
TEST=Book elm-rev1
Change-Id: Ib106924418b16388ea8ea53c7b6bda6ef92e1d09
Signed-off-by: Nicolas Boichat <drinkcat@google.com>
Reviewed-on: https://chromium-review.googlesource.com/345761
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Randall Spangler <rspangler@google.com>
Enabled CONFIG_CMD_RTC_ALARM. EC_HOST_EVENT_RTC
is enabled when the rtc_alarm goes off,
alerting the AP to transition from S3->S0.
BUG=chrome-os-partner:52218
BRANCH=None
TEST=rtc_alarm <num> and see event set in ec console
after <num> seconds. Also, check if new bit set
through hostevent command in ec before/after
rtc_alarm goes off.
Change-Id: I53b1705ce0925000f35b9f80752035d198db3310
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/345474
Reviewed-by: Shawn N <shawnn@chromium.org>
LPC access interrupt only enabled when EC entering deep doze mode. This
will reduce interrupt of LPC access. Also, this interrupt is always
enabled for LPC platform to support "CONFIG_LOW_POWER_S0".
Signed-off-by: Dino Li <dino.li@ite.com.tw>
BRANCH=none
BUG=none
TEST=Tested ectool command 'version' x 10000.
Change-Id: I9053c4018b38a8a852c3c6254e1fcde625f3fa3a
Reviewed-on: https://chromium-review.googlesource.com/336112
Commit-Ready: Dino Li <dino0303@gmail.com>
Tested-by: Dino Li <dino0303@gmail.com>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Driver implements TCPC for ANX74xx chips. Enables Type C
port for USB and DP alt mode. Enable port role swap feature.
Driver implements TCPC for ANX74xx chips firmware version 1.0 and later.
Please update to ANX74xx firmware to V1.0 or later version to work.
Change list:
1, modify the position of define and struct declare
which response the comment for patch 22.
BUG=chrome-os-partner:49510
BRANCH=none
TEST=tested compiled binary for pdeval-stm32f072 board with this patch.
Power contract establishment, port role swap, DP alt mode works fine.
Change-Id: Iae6322510605a08d3bdd08446116ef5f9e4f7a7c
Signed-off-by: Aman Kumar <akumar@analogixsemi.com>
Signed-off-by: Junhua Xia <jxia@analogixsemi.com>
Reviewed-on: https://chromium-review.googlesource.com/322433
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
The maximum length of console command name is hardcoded to be 14 in a
few places in the code. In any case, 14 characters should be enough
for any command name, let's add compile time check to ensure that this
limit is honored.
BRANCH=none
BUG=none
TEST=tried adding a command with a name longer than 14 characters, got
a compile error.
Change-Id: I11891fcd04983a5618400a602d4b80a478ecf3a9
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/345571
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Previously usb_charger.c supported only pi3usb9281, but now support for
additional parts is required. Move pericom-specific code (including the
usb_charger tasks that handles various quirks of that part) to the
pi3usb9281 usb_switch driver.
Going forward, usb_switch drivers must implement
usb_charger_set_switches() and must have some method (such as a task or
interrupt handler) to update charge_manager with information about
attached chargers.
BUG=chrome-os-partner:53363
BRANCH=None
TEST=`make buildall -j`
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I4df74e043d8cf2e532d48c39c73b7dc2930f7d3b
Reviewed-on: https://chromium-review.googlesource.com/344289
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Add generic PWM host commands for setting + getting duty cycle. PWMs can
be controlled through index (board-specific meaning) or by type
(currently KB backlight and display backlight are supported, more can be
added as needed).
BUG=chrome-os-partner:52002
BRANCH=None
TEST=Manual on chell.
`ectool pwmsetduty kb 100` - Verify KB backlight goes to 100%
`ectool pwmgetduty kb` - Prints 100
`ectool pwmgetduty 0` - Prints 100
`ectool pwmsetduty 0 0` - Verify KB backlight goes to 0%
`ectool pwmgetduty kb` - Prints 0
`ectool pwmgetduty disp` - Error res 3 (unsupported PWM type)
`ectool pwmsetduty 1` - Error res 3 (non-existent PWM index)
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I607c92a291e6c2e3af8238eaf22ad2bb81ffc805
Reviewed-on: https://chromium-review.googlesource.com/344012
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Mary Ruthven <mruthven@chromium.org>
Using HOOK_PRIO_DEFAULT for peripheral initialization necessitates using
HOOK_PRIO_DEFAULT+1 for board-level code. Instead, use a
higher-than-default relative priority for peripheral initialization
outside of board.
BUG=None
TEST=Verify PWM and ADC are functional on kevin.
BRANCH=None
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Ia8e90a7a866bdb0a661099dd458e3dfcaaa3f6bb
Reviewed-on: https://chromium-review.googlesource.com/342171
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Shawn N <shawnn@chromium.org>
add optional chipset specific function to check if PLTRST# is valid
BUG=chrome-os-partner:52656
BRANCH=none
TEST=make buildall, able to boot to OS on amenia
Change-Id: I7a2747c4f77f50393c3250c2ab0e1625e64e5a41
Signed-off-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/341732
Reviewed-by: Shawn N <shawnn@chromium.org>
This change modifies the behavior of RBOX by blocking the key0 and key1
output, when the power button is pressed. It also adds support for
printing debug statements when various RBOX interrupts are triggered.
BUG=none
BRANCH=none
TEST=On cr50 test board verify key0 and key1 out are not asserted unless
the power button is pressed.
Change-Id: I67a3c1b8009279015bdc87bcf0995cffa9ab6f03
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/341470
Tested-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
Add PWM_CONFIG_DSLEEP PWM config flag, which can be set to keep a
channel active during low-power idle / deep sleep. Currently it's
supported by npcx and mec1322.
BUG=chrome-os-partner:52783
BRANCH=glados
TEST=Manual on chell w/ subsequent commit + CONFIG_LOW_POWER_S0. Verify
KB backlight does not flicker during idle.
Change-Id: Ib9df5879aaa7dfa5764de1583496de84d40d2bb5
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/341002
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
GPIO console commands currently only show input voltage level,
and can only set level on predefined outputs.
This change allows GPIOs to be cycled between output, input,
and alternate function, as well as displaying the mode and
asserted level (if any) in gpioget.
This change creates CONFIG_CMD_GPIO_EXTENDED
as the internal gpio interface needs to be changed to support
this, and I can't test the other architectures. It may be
worthwhile to add this for all, or not.
This change is also necessary also for servo micro JTAG and PD
UART support, as several pins are tied together on the flex
and stm32 outputs need to be variously active or in high-z
depending on mode.
BUG=chromium:571477
TEST=gpioget <0|1|IN|A|ALT>; gpioget;
BRANCH=None
Change-Id: Iba32992db6244ee1e654db840d1c9c11dd2a0993
Signed-off-by: Nick Sanders <nsanders@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/338885
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
The cr50 SPI master can control the external AP and EC SPI ROM. This
change adds support for doing spi_transactions, but does not use the SPI
transactions for anything except console commands. This support will be
used for flashing the AP and EC through CCD. For now AP and EC flash
select must be done manually using the spi_flash_select console command.
Flash select should be disabled after use, because it will prevent the
system from booting.
BUG=chrome-os-partner:50701
BRANCH=none
TEST=Enable spi_flash commands. Select AP ROM and verify spi_flashinfo,
read, erase, and write commands work properly. Select EC ROM and verify
the same commands.
Change-Id: I16c55015794f8513effe0fa5712488a84bed2627
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/339844
Reviewed-by: Shawn N <shawnn@chromium.org>
This patch adds initial set of files to bring up STM32L476G-Eval board.
BUG=none
BRANCH=tot
TEST=Tested console. make buildall && make tests
Change-Id: I0c0f73f31e84099746fced4214c5ed7f45468cef
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/340100
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Previously the maximum number of deferred routines was specified by the
the default maximum number of deferred routines you had to override
this, and if you wanted fewer, you still payed the price of having the
defer_until array statically allocated to be the maximum size.
This change removes that define and instead creates the RAM state of
the deferred routine (the time to wait until to call the deferred) when
the deferred is declared.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
manually test on discovery-stm32f072
Change-Id: Id3db84ee1795226b7818c57f68c1f637567831dc
Reviewed-on: https://chromium-review.googlesource.com/335597
Commit-Ready: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Previously calls to hook_call_deferred were passed the function to call,
which was then looked up in the .rodata.deferred section with a linear
search. This linear search can be replaced with a subtract by passing
the pointer to the deferred_data object created when DECLARE_DEFERRED
was invoked.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
CQ-DEPEND=CL:*255812
TEST=make buildall -j
Change-Id: I951dd1541302875b102dd086154cf05591694440
Reviewed-on: https://chromium-review.googlesource.com/334315
Commit-Ready: Bill Richardson <wfrichar@chromium.org>
Tested-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
The device-specific subclass used for Non-HC firmware updates is
in the spreadsheet now, so we can rename the macros to be
"official".
BUG=chrome-os-partner:49962
BRANCH=none
TEST=make buildall; test on cr50
make BOARD=cr50 (plus whatever signing magic works for you)
make -C extra/usb_updater
./extra/usb_updater/usb_updater build/cr50/ec.bin (sudo if needed)
Note that you may need to rebuild ec.bin in order to see any
difference after the update. If the A & B images are identical,
the RO bootloader always picks A.
Change-Id: I385ce89a9abe2059d52da2d82a0b92b9b3e3c93f
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/339220
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Add support for SHA256 based HKDF key
derivation as specified in RFC 5869. This
change includes test vectors from the RFC.
BRANCH=none
BUG=chrome-os-partner:43025,chrome-os-partner:47524
TEST=tests under test/tpm2 pass
Change-Id: I7d0e4e92775b74c41643f45587fc08f56d8916aa
Signed-off-by: nagendra modadugu <ngm@google.com>
Reviewed-on: https://chromium-review.googlesource.com/336091
Commit-Ready: Nagendra Modadugu <ngm@google.com>
Tested-by: Nagendra Modadugu <ngm@google.com>
Reviewed-by: Marius Schilder <mschilder@chromium.org>
This adds support for RD Detection on cr50. It can be used to detect a
debug device and signal the controller to switch from the AP PHY to the
to CCD PHY. When RDCC1 and 2 no longer detect the debug device, then
the controller switches back to using the USB to AP PHY.
BUG=chrome-os-partner:50700
BRANCH=none
TEST=change the value on RDCC1 and RDCC1 and check that the usb
controller connects to the right PHY.
Change-Id: Ice01a45a31fe1932945f89df2e3b851f4d287a17
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/338454
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
This enables the Cr50 to accept RW firmware updates over USB.
BUG=chrome-os-partner:50707, chrome-os-partner:50712
BRANCH=none
TEST=make buildall; test on Cr50
Build and run the extra/usb_updater utility. Watch the console,
and observe that the Cr50 updates and reboots into the new image
correctly.
Note that you'll have to rebuild the ec.bin image in order for
the update to take effect. Just reflashing the same image doesn't
cause the bootloader to change its selection.
All the previously existing endpoints continue to function normally.
Change-Id: I7bd22eae803c2ceeb14a767c06d3d5c9f1ac7c7a
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/338089
Commit-Ready: Vadim Bendebury <vbendeb@chromium.org>
This re-factors the existing firmware upgrade facility, which worked as
a TPM command extension.
The same code processing upgrade blocks prepended by the truncated
SHA1 and the load address is now used by both extended TPM command and
the USB upgrader.
To accommodate USB communications using a smaller message payloads a
reassembly layer is introduced which accumulates short USB payloads
into a single block which can be passed to the firmware upgrade
routine. USB encapsulation adds one 4 byte header at the beginning of
the block to hold the total block size. The reassembly layer keeps
receiving USB messages, concatenating their payloads until the full
block is received.
A config option is added to make sure the module is not compiled when
not needed.
BUG=chrome-os-partner:50707
BRANCH=none
TEST=make buildall; test on Cr50 - with the rest of the patches
applied it is possible to upgrade firmware using the USB utility
on the host..
Change-Id: Ib30b381c4ab196ea9d352f3c6b8f46dc23ddd599
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/338087
The scheme to disable PD communication in locked RO needs to be
implemented on other platforms, so move it to common code, behind
CONFIG_USB_PD_COMM_LOCKED.
BUG=chrome-os-partner:52157
BRANCH=glados
TEST=Manual on chell. Lock system and boot to recovery, then verify PD
communication is functional. Enable CONFIG_USB_PD_COMM_LOCKED and verify
PD communication isn't functional under the same test conditions.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I8d1f24c0b60cf1c54e329af003b7083ee55ffc40
Reviewed-on: https://chromium-review.googlesource.com/338064
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
If we #define CONFIG_RW_B, the firmware image can have two RW
components. This CL expands the "sysinfo" command so that we can
see which image we're running from when RW_B is also a
possibility.
BUG=chrome-os-partner:50701
BRANCH=none
TEST=make buildall; test RW update on Cr50
Using test/tpm_test/tpmtest.py, update the RW firmware and reboot
several times to switch between RW_A and RW_B. Note that the
"sysjump" command reports the correct image each time.
Change-Id: Iba3778579587f6df198728d3783cb848b4fd199d
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/337664
Reviewed-by: Randall Spangler <rspangler@chromium.org>
CR50 will need three serial endpoints for the streaming AP and EC UART
and exporting its own console through USB. This change adds a macro to
create endpoints that can be recognized by the usb_serial driver.
BUG=chrome-os-partner:50702
BRANCH=none
TEST=Verify "/dev/google/Cr50*/serial/Blob" prints capital letters when
lower case letters are input.
Change-Id: Iddf2c957a00dc3cd5448a6a00de2cf61ef5dd84c
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/336441
Tested-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@chromium.org>
modify g781.c/.h to g78x.c/.h to suppor both G781/G782 temp sensor
based on CONFIG_TEMP_SENSOR_G781 or CONFIG_TEMP_SENSOR_G782
BUG=none
BRANCH=none
TEST=make buildall; able to get temperature data on board with G782
Change-Id: Ia32c85e9964bfd7c0c5263f04368bc001a27fe10
Signed-off-by: Kevin K Wong <kevin.k.wong@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/334228
Reviewed-by: Shawn N <shawnn@chromium.org>
