The exact behaviour still needs to be optimized based on actual
power consumption (for example, it might be worth providing power
to base without charging it, or charge it a bit more, then let
it slowly discharge).
BRANCH=none
BUG=b:71881017
BUG=b:74414928
TEST=Low base battery, check that lid provides power to it in S0 or
suspend.
TEST=Check that lid stops providing power in S5.
Change-Id: Idf198ab1b4358827f9db6c0898234b6e2be45808
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/956982
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
When the base battery is low, we need to provide it with some power,
to make sure the battery does not fully deplete.
Instead of relying on a separate configuration value, we simply
reuse min_base_system_power. Also, we fix a bug that incorrectly
used a power value as current.
BRANCH=none
BUG=b:71881017
BUG=b:74414928
TEST=With a critically low wand (3%), lux is able to provide
enough power to charge wand battery a little (44mA), even
when backlight is fully on, and touchpad is in use.
Change-Id: I3174ac273712eeb83ce1283dda3d786ad503e6f3
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/956661
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
If the I2C port is completely broken then there is no point in trying to
continue with the transaction. This can happen if the pull-ups on the bus
are not working because they are in a power domain which is not currently
enabled.
Check the return value from i2c_unwedge() and return if it doesn't work.
Tidy up a few comments at the same time.
BUG=b:72129419
BRANCH=none
TEST=manually remove the check AP being off in sb_tsi_get_val() and see
that it quickly fails now, rather than hanging the EC for a while trying
the transaction.
Change-Id: I66ab52943459726537dfc74355f8aeaa5817dba5
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/956017
Reviewed-by: Edward Hill <ecgh@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Without this patch, requesting 100mA or output current would be
rounded down to zero.
This would also cause other issues when doing base/lid and lid/base
power transfers on lux/wand, as the input current has a much finer
grain control, which could lead the input charger to brown out
the output charger.
BRANCH=none
BUG=b:67920792
TEST=Flash lux/wand, lux can provide as little as 100mA of current
successfully.
Change-Id: Ibf170a6ee3c2dfbdbbc03948c3b0e6ab878eee47
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/956660
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
If wand ever reaches low enough battery level (<3%), it should
hibernate, instead of cutting off the battery, as the latter will
disable all the switches, and lead lux to redetect the base.
BRANCH=none
BUG=b:74414928
TEST=Discharge wand as much as possible, then put lux in S0ix (no
power transfer currently), discharge wand further (using
pwm 0 100 to activate backlight to draw a bit more power),
see that wand goes into hibernate.
Change-Id: I9edb517aada7d21fbcddbce4ad06ab7fbcafce38
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/956659
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Since we only enable power to the base in the charger task (we
can't enable power before OTG/power allocation is setup properly),
there is a potential race when we quickly plug/unplug the base.
Fix this by only allowing the enable power when the detection
code knows that the base is actually connected.
BRANCH=none
BUG=b:74403503
TEST=Plug/unplug wand several times with charger attached,
PPVAR_VAR_BASE is always 0 whenever the base is disconnected.
Change-Id: I96da9ed39ddbbbe7aea54ad96c62fde6115538c0
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/956204
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
At present issuing several 'waitms 1000' commands immediately after each
other trips the watchdog. Add a watchdog reload to avoid this.
Also document the behaviour in the command help.
BUG=b:72542719
BRANCH=none
TEST=manually on grunt, pasting these three lines in:
waitms 1000
waitms 1000
waitms 1000
and see that it does not reset now.
Change-Id: I453708299e4e26c1bbdb5fc406f26e916e7389af
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/955927
Reviewed-by: Edward Hill <ecgh@chromium.org>
Reviewed-by: Martin Roth <martinroth@chromium.org>
The port_address field is used in the driver. Also making array
declaration consistent with other parts of the file.
BRANCH=none
BUG=none
TEST=none
Change-Id: I43c72182c6afefbdbb7286918326b7ea6f92c7d7
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/955940
Reviewed-by: Edward Hill <ecgh@chromium.org>
list/add_activities should be include even when FIFO support is not
compiled it, when the host is not asking for them, as it is needed for
double tap support.
BUG=b:73546254
BRANCH=master
TEST=Compile when just CONFIG_GESTURE_DETECTION is defined.
Change-Id: Icec7ccec7fd8463ea40afbe05ce1e177ae7d609d
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/924404
Commit-Ready: Gwendal Grignou <gwendal@google.com>
Tested-by: Gwendal Grignou <gwendal@google.com>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@google.com>
Add support for generating the authcode from cr50's challenge.
BUG=b:74019846
BRANCH=none
TEST=create a cr50 image with test keys. Verify that the output from
rma_reset -c opens cr50.
Change-Id: I85a209e55dc23daa118e0071e868878b6fbfcb69
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/945419
Reviewed-by: Randall Spangler <rspangler@chromium.org>
To enable USB charging on boards where fusb302 takes care of VBUS detection
BUG=b:65446459
BRANCH=none
TEST=on Scarlet rev3, verify VBUS supplier is updated based on
whether VBUS is present - plug/unplug USB2 charger, boot with USB2
charger plugged.
Change-Id: I50177d40b0eb0490634ad2f103306e0079633fbe
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://chromium-review.googlesource.com/905401
Commit-Ready: Philip Chen <philipchen@chromium.org>
Tested-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Add support for setting the battery to discharge even if AC is
present. Used for factory testing.
BRANCH=none
BUG=b:74096137
TEST=ectool chargecontrol discharge, ectool battery
Change-Id: I79e6bfabcfc0327e5c12c789decc27591911a6ee
Signed-off-by: Edward Hill <ecgh@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/954283
Reviewed-by: Cheng-Han Yang <chenghan@chromium.org>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Ensure that the short parameter '-p' works as well as the long one
'--progressbar'.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=run 'stm32mon -p' and 'stm32mon --progress' none of them are
displaying the command usage.
Change-Id: If24accf0991dc9705a1fb3e29acf12581d7ab8dc
Reviewed-on: https://chromium-review.googlesource.com/952966
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Nicolas Norvez <norvez@chromium.org>
Some boards have forgotten to undef CONFIG_PECI but it is benign. This
should be an opt-in feature instead of an opt-out feature. No one is
using it, so no one will opt-in.
BRANCH=none
BUG=none
TEST=Verified that grunt, kahlee, meowth, and zoombini are not using the
PECI bus for Soc temperature via schematics (GPIO81). Other boards are a
no-op. See cl:951407 for steps taken to ensure all npcx boards were
accounted for.
Change-Id: I6ca4b9d22b7cb23c9842729658810ebe165ff6cc
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/951408
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Currently cbi-util accepts only fixed length values. This patch makes
it automatically calculate the required field size to accomodate the
given integer value.
The stored values are expanded to uint32_t when they're read.
BUG=b:74174598,b:70702820
BRANCH=none
TEST=Run cbi-util with --sku_id set to the followings:
0x10 -> field size = 1,
0x1000 -> field size = 2,
0x10000 -> field size = 4,
0x100000000 -> Error
Change-Id: I2221ebfa18260bae2c574d9ebb794dbe645579e5
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/951711
Reviewed-by: Randall Spangler <rspangler@chromium.org>
When the EC sends back an error code inside the 'result' field of the v3
protocol, the transport is supposed to return -EECRESULT-error_code.
Fix the the servo spi transport to do so.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=b:72360575
TEST=with ZerbleBarn connected to a Servo v2, run 'ectool_servo fpinfo'
and 'ectool_servo fptemplate badfile.bin'
Change-Id: I54eec9194cfefd422078344500685736aadaffcf
Reviewed-on: https://chromium-review.googlesource.com/951682
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This patch splits struct fan_t into two parts: base configuration
and RPM configuration. RPMs are expected to be different from
model to model while a base configuration is most likely shared.
BUG=b:73720175
BRANCH=none
TEST=make buildall
Change-Id: Iff17573f110e07e88d097dd848cf91ee98b83176
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/949382
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
The CONFIG_UART_HOST is supposed to be defined to the index of the UART we
want to use. It is not supposed to be defined as a boolean. Updated npcx
and all incorrect uses.
BRANCH=none
BUG=none
TEST=Added the following diff to ensure that everything still built:
diff --git a/chip/npcx/lpc.c b/chip/npcx/lpc.c
index 446baa842..826233744 100644
--- a/chip/npcx/lpc.c
+++ b/chip/npcx/lpc.c
@@ -897,6 +897,9 @@ static void lpc_init(void)
/* Initialize Hardware for UART Host */
#ifdef CONFIG_UART_HOST
+#if !CONFIG_UART_HOST
+#error "Fix me"
+#endif
/* Init COMx LPC UART */
/* FMCLK have to using 50MHz */
NPCX_DEVALT(0xB) = 0xFF;
Change-Id: Ia46c7cb86c6040a5c75dddf23d5ccd8e33210581
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/949308
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Remove the former special case for USB RAM
Add additional RAM regions for STM32H7.
For USB RAM, add an explicit alignment directive to ensure we always meet
the 8-byte boundary hardware constraint for the BTABLE.
This was already true because we put the .usb_ram.btable section first.
I keep this property by alpha-sorting the sections but makes it more
explicit by adding a 2-digit numeric prefix: e.g. 00_firstsection,
99_lastsection.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=b:67081508
TEST=on ZerbleBarn, along with the following CLs, run the firmware with
large arrays in special AHB memory regions.
TEST=build all targets with and without the patch and verify that all
smap files are identical.
Change-Id: I9ee7f519a13cb14ba9997220f22180028f9c0175
Reviewed-on: https://chromium-review.googlesource.com/946369
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
When a chip has special/non-contiguous SRAM physical memory region,
rather than extending the generic linker file ad nauseam, define a
mechanism to declare a chip specific list of those regions.
To do so, a chip must declare the CONFIG_CHIP_MEMORY_REGIONS
configuration and have a memory_regions.inc with the list of regions.
The special-purpose preprocessed chip/<chip_name>/memory_regions.inc
file has one region declaration per line using the following macro:
REGION(name, attributes, start_address, size)
Each region will get a proper MEMORY entry and a section in the linker
file.
the __SECTION(region_name) helper is provided as a convenience to
declare variable in a specific region.
Note: those 'special' regions are NOT cleared at startup contrary to
.bss.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=b:67081508
TEST=on ZerbleBarn, along with the following CLs, run the firmware with
large arrays in special AHB memory regions.
Change-Id: I3f156ef6e5feb4a6a0b2ae2468bae8a20483f17c
Reviewed-on: https://chromium-review.googlesource.com/946368
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Make it clearer what the new key is about.
CONFIG_KEYBOARD_NEW_KEY to CONFIG_KEYBOARD_ASSISTANT_KEY.
BRANCH=none
BUG=none
TEST=make buildall -j
Change-Id: Ic2db425b40ff8bc612626b6f644463b1f8ec630e
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/950263
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Cr50 lacks native instructions for 64-bit integers and an ABI
function can be used by the compiler to take the place of the
needed instructions. This CL adds support for a right bitwise
shift of 64-bit integers.
BRANCH=none
BUG=chromium:794010
TEST=Set CONFIG_LLSR_TEST, build, update cr50, and run llsrtest
on the console.
Change-Id: Iae66c86720c531454ba29f15b3cc6a07959f5ef2
Signed-off-by: Allen Webb <allenwebb@google.com>
Reviewed-on: https://chromium-review.googlesource.com/931932
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
There's a new pin being added for board versions. Additionally, the
endianness is different than what was implemented.
BUG=b:73260349
BRANCH=stabilize-meowth-10444.B
TEST=Flash meowth; verify board version is as expected.
Change-Id: I97fb66f6c6aaf20d0ea4ed5994301490234ab812
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/949054
Commit-Ready: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
BRANCH=none
BUG=b:73528930
BUG=b:73660652
TEST=Flash lux, check that lux adc VBUS voltage when only no
charger is connected is around 12V.
Change-Id: Iccc245c96ca3c83674446f96f78f1ce15ffa7de2
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/948322
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Add a new module ID 'MODULE_FAST_CPU'.
When it is enabled with clock_enable_module(MODULE_FAST_CPU, 1), switch
the system clocking to the fast 400-Mhz PLL.
For now, I consider that a single task/user is calling
clock_enable_module(MODULE_FAST_CPU, x), so we don't need to count users
(in a complicated atomic fashion). It's good enough for the current
use-case and we can add the complexity later if we have a real need.
BRANCH=none
BUG=b:67081508
TEST=on ZerbleBarn, with follow-up CL setting
clock_enable_module(MODULE_FAST_CPU,x) around the computation block,
see that computations are fast and the clock goes back to HSI after.
Change-Id: I2aef3ad673ddbffd6fc64c591c54297e94896fa6
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/945688
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Set the PLL frequency to 400 Mhz (max value) and the AHB frequency to
200 Mhz.
Fix the PLL clocking code for STM32H7 :
- fix the frequency computation.
- adjust the timer divider depending on the system clock.
- the 64Mhz HSI is already setup properly at startup, takes it into
account.
- set the SPI ports on the fixed 64-Mhz HSI, so clocking changes don't
mess up their frequencies or stability.
Note: this is just modifying the CPU frequency when the system is
clocked by the PLL, by default the system is still clocked by the 64-Mhz
HSI. Currently, one have to use the 'clock pll' console command to test
this PLL mode, some code will be added soon to switch on-demand for
heavy computations.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=b:67081508, b:72879097
TEST=On ZerbleBarn, do 'clock pll', check 'gettime' against wall clock,
run image capture and enrollment.
TEST=on ZerbleBarn, verify on the scope that the SPI master frequency is
4 Mhz in both configuration.
Change-Id: I92a2216999337cf9831fb5dfc2797ab1cce71a8f
Reviewed-on: https://chromium-review.googlesource.com/941226
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
1. Enable fan feature and update fan setting.
2. Enable SW and chipset throttle feature.
3. Fix the issue that cannot set fan duty by "fanduty" in EC console.
BUG=b:72974136
BRANCH=none
TEST=Check fan command(fanduty/fanset/fanauto) in EC console can work and
check below condition.
1.AP throttling soft
--> Increased temperature to over trigger point, then to check
EC notify event in EC console.
2.AP throttling hard
--> Increased temperature to over trigger point, then to check
EC notify event and CPU_PROCHOT pin status in EC console.
3.Fan controlled in s3/s5 as expected (by EC)
--> Check Fan turn off in s3/s5.
4.Fan controlled in S0 as expected (by DPTF)
--> Check Fan keep 100% duty and no see DPTF to set fan duty.
But fan duty can be control by "fanduty" in EC console.
Change-Id: If9fd7f64c123ff54742052b6310023f0d4b0113a
Signed-off-by: raymondchou <raymond_chou@compal.corp-partner.google.com>
Reviewed-on: https://chromium-review.googlesource.com/906086
Commit-Ready: Raymond Chou <raymond_chou@compal.corp-partner.google.com>
Tested-by: Raymond Chou <raymond_chou@compal.corp-partner.google.com>
Reviewed-by: Raymond Chou <raymond_chou@compal.corp-partner.google.com>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
NPCX7 requires that the HW_WIRE bits 2-0 of VWEVSM2 register are set
so that the hardwire signals for SCI, SMI and RCIN are connected to VW
input of eSPI_SIF module. NPCX5 did this by default, however NPCX7 has
made it configurable.
NPCX7 however sets the HW_WIRE bits 2-0 to 1 at reset. So, this change
ensures that they are preserved while initializing VWEVSM2 registers
BUG=b:74111394
BRANCH=None
TEST=Verified that SCI works on glkrvp and meowth with NPCX7.
Change-Id: I9da6f45b4aa0b72b68db6192cb7567f09b072f0c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://chromium-review.googlesource.com/943801
Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Tested-by: Divya S Sasidharan <divya.s.sasidharan@intel.com>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: ML Chao <mlchao@nuvoton.corp-partner.google.com>
Reviewed-by: Jett Rink <jettrink@chromium.org>
When checking the RMA authentication code the code currently just
verifies the value, but does not act on it.
This patch directs the user input through the same vendor command path
which is used when the RMA operation is controlled using gsctool.
BRANCH=cr50, cr50-mp
BUG=b:74080723
TEST=verified that issuing 'rma_auth <code>' on the Cr50 console now
trigger CCD open and reboot.
Change-Id: Ib3fab131b6a24b65618f0b1f2504638f8df11a4b
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/945311
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The ARMv7-M ISA defines standard (and optional) mechanism to manage the
CPU caches through the SCB (System Control Block) registers.
So far, only the Cortex-M7 core implements such as a mechanism (e.g. the
Cortex-M4 with caches we have are using a proprietary mechanism for the
management).
Define the functions to use the I-Cache,
and enable them on STM32H7 which is our only supported Cortex-M7 core.
The D-Cache mechanism is still To Be Done, as it involves a bit more
support in the firmware for the DMA memory areas.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=b:67081508
TEST=on ZerbleBarn, verify manually that the 'IC' bit is set in the CCR
(e.g. 'rw 0xe000ed14' returns 0x60218), and runs some CPU workload
without crash and with a speed-up.
Change-Id: I6af1021d65048b787630387f7d95797db15d069c
Reviewed-on: https://chromium-review.googlesource.com/943445
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The DBP bit needs to be set in the PWR_CR1 register before doing the RTC
configuration (in order to be able to right RTC registers).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=b:67081508
TEST=on ZerbleBarn, dump the RTC_TR register and it is incrementing
every second, e.g. 'rw 0x58004000'.
Change-Id: I02dc6c6f1852ced934bccf3e401f4fdc1aad57d9
Reviewed-on: https://chromium-review.googlesource.com/941224
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Set GscFullConsole to Always in RMA open. We need this to be accessible
after rma open, so that we can use RMA open as a ccd open testlab
replacement.
Commands like rddkeepalive and bitbang are needed for testlab use, so
they should be accessible after open.
BUG=b:74019846
BRANCH=cr50, cr50-mp
TEST=build, do rma open, verify commands are not locked out, and do rma
disable
Change-Id: Iaeb89cea94d478dc0eb25c92bb09d488d14cad41
Signed-off-by: Mary Ruthven <mruthven@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/942309
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Move the RW signature verification in a dedicated task rather than on
the synchronous startup path, in order to be compatible with our flashrom
update mechanisms (but at the expense of additional latency in RO).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=b:36125319
TEST=flashrom -p ec:type=fp -w ec.bin
Change-Id: If9ae66bfde0c5922db86dc9acfd4ee766089fa1d
Reviewed-on: https://chromium-review.googlesource.com/936542
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Also define the EC_FEATURE_RWSIG feature bit if the RO firmware contains
the RWSIG task but not the RW.
Given the RWSIG verification task is not terribly useful in RW
(where it is never executed), it can be skipped there but the host
program trying to detect RWSIG usage (e.g. flashrom) still wants to be
able to detect it.
In order to be able to do so, add the HAS_TASK_xXx_RO and
HAS_TASK_xXx_RW flags which define the tasks defined in the other
partition (at compilation-time you might still run a frankeinstein combo).
Fix ectool 'inventory' to avoid segfaulting on missing feature string
definition.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=b:36125319
TEST=on ZerbleBarn, run 'ectool inventory', also uses flashrom to
re-flash the RW partition.
Change-Id: I224a6cc4aef956204792a2cc04ad12aaed5abf47
Reviewed-on: https://chromium-review.googlesource.com/937262
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Using only a Carriage Return as done to have a nice spinner is not
terribly compatible with logging the output of the tool to a file or
piping it to anything.
Add another option to have a simple progress-bar instead.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=on Meowth, run flash_fp_mcu from the factory UI.
Change-Id: I0c37689d2ed1e45dff54b7f1eb2be515ea37e004
Reviewed-on: https://chromium-review.googlesource.com/936766
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Nicolas Norvez <norvez@chromium.org>
The shmem console command was looping with the wrong iterators,
doing an infinite loop when there was more than one allocated or
free block.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
BRANCH=none
BUG=none
TEST=build software with CONFIG_MALLOC and CONFIG_CMD_SHMEM, then run
'shmem' on the console at different time without hitting watchdog reset.
Change-Id: I93a9cff3811669ab895fa8753d1571e90aeb4f33
Reviewed-on: https://chromium-review.googlesource.com/943070
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
