This CL locks VCC_RST# alternative bit, NO_VCC1_RST, of DEVALTA
in case the developers switch it to GPO77 unexpectedly by setting
VCC1_RST_LK bit in DEV_CTL4.
BRANCH=none
BUG=none
TEST=Use rw console command to make sure NO_VCC1_RST bit is
locked on npcx7_evb.
Change-Id: Ic7882ef1c8050c3daca85bd241d5368f009e4e2e
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/522206
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This CL adds:
1. Fixed the incorrect address of BKUP_STS register.
2. Cleared the IBBR bit of BKUP_STS register at initial because
its default value is 1(means the content of BBRAM is invalid) whenever
VBAT is powered up.
3. Add debug msg when IBBR bit is set to indicate the BBRAM's
corruption.
4. Modified the valid BBRAM offset from 1 to 0 and size from 63 to 64.
BRANCH=none
BUG=b:38187362
TEST=No build error for make buildall; Check IBBR is cleared at initial.
Check IBBR is set by changing the VBAT voltage below VBAT MIN.
Test console command "reboot ap-off" on poppy.
Change-Id: I69d98b50d4e0aec17b55a4a9b5e8f1a412a3fe45
Signed-off-by: CHLin <CHLIN56@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/505861
Commit-Ready: CH Lin <chlin56@nuvoton.com>
Tested-by: CH Lin <chlin56@nuvoton.com>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
In order to support write-protect mechanism for the internal flash
of npcx7 ec, WP_IF, bit 5 of DEV_CTL4, is used to achieve this by
controlling the WP_L pin of internal flash. During ec initialization
or any utilities related to access status registers, we'll protect them
if WP_L is active. Please notice the type of WP_IF is R/W1S. It means we
only can unlock write protection of internal flash by rebooting ec.
This CL also includes:
1. Add protect_range array of npcx7's internal flash (W25Q80) for
write-protect mechanism.
2. Add bypass of bit 7 of DEVCNT.
BRANCH=none
BUG=none
TEST=No build errors for all boards using npcx5 series. (Besides gru)
Build poppy board and upload FW to platform. No issues found.
Passed flash write-protect checking on npcx796f evb.
Change-Id: I0e669ce8b6eaebd85e062c6751e1f3dd809e21e2
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/501727
Reviewed-by: Randall Spangler <rspangler@chromium.org>
This CL includes:
1. Add gpio_chip-npcx5/7.h files and move all macro functions
related to chip family to them. (Move wui macro func from
gpio_wui.h to them.)
2. Replace alternative and low-voltage mapping table with macro
function NPCX_ALT_TABLE and NPCX_LVOL_TABLE.
3. Add UART wakeup mechanism in __gpio_wk1h_interrupt() ISR.
4. Add gpio register definitions of npcx7 family in registers.h.
5. Add GPIO_LOCKED flag for lock functionality.
BRANCH=none
BUG=none
TEST=No build errors for all boards using npcx5 series (besides gru).
Build poppy board and upload FW to platform. No issues found.
Passed validation for all GPIO functionalities on npcx5m6g
and npcx796f evb.
Change-Id: I60c30ce223629a0d8cb767a54a0a9b02a69de9c5
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/481561
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
In npcx's fan driver, ec selected mode 5 and capturer A as tachometer's
input. Choosing TB2 as the second tachometer source is not correct since
we didn't initialize the registers for TB2. This patch modified the
second tachometer's input from TB2 to TA2 and passed the verification by
following changes.
1. Add the second fan settings in pwm_channels, fans, and mft_channels
arraies.
2. Modified ALTERNATE marco for pwm-type fans.
3. Set CONFIG_FAN from 1 to 2.
4. Set NPCX_TACH_SEL2 to 1 to test tachometer input 2. (ie.GPIO73/A6)
BRANCH=none
BUG=none
TEST=test dual fans with fanset command on npcx_evb and use faninfo for
verifying. Measure the actual rpm by scope.
Change-Id: Ia1af2732d9a64e24285d12371223eb0e77e53357
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/472310
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Setting PWM IO type in gpio driver seems not a proper way. This
CL moves this functionality to pwm driver and introduces a new
flag PWM_CONFIG_OPEN_DRAIN to achieve it when user declared it
in board driver.
BRANCH=none
BUG=none
TEST=test pwm functionality on npcx_evb.
Change-Id: I90c60445d1fb10902244ddf0f635d8304e72f4ab
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/458043
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
By generating the wui mapping table for GPIO pins which have interrupt
handler like CL 451366 did, we needn't browse all items in original
gpio_wui_table to find the MIWU info. It saves code space and improves
interrupt lantency.
BRANCH=none
BUG=none
TEST=Test gpio functionality on npcx_evb, reef and poppy.
Change-Id: I77e9ad439ecf6a501a7976fe5099dd309dba81ee
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/449514
Since the interrupts of MIWU group E/F/G/H of table 0 are the same
(interrupt 11), we need to handle LPCs' and GPIOs' events at the
same ISR. But we also found there is a leak that ec has the chance
to skip the other events which don't belong to GPIOs unexpectedly.
(For example, LRESET and eSPI Reset) This CL fixed this issue by
only clearing pending bits belong to GPIOs in their ISRs.
BRANCH=none
BUG=b:35648154
TEST=passed warm-reset testing on pyro over 12 hours.
Change-Id: Ie626db00b54cff566798b4a593f6b0267a6fadc2
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/449472
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Currently if an interrupt is pending before it is enabled the interrupt
will fire immediately. In most cases this is fine, but if we want to
use the interrupt to trigger something like waking the AP it should be
sure that it won't immediately fire once enabled.
For example: on the Eve board we have the trackpad interrupt run to the
AP and the EC in order to support wake from Deep S3 (magic AP state that
only the EC can wake it from). This interrupt is used in S0 by the AP
while ignored by the EC, and then enabled on the transition to S3 in
order to be able to wake. Since it has been active the interrupt may
be pending in the EC (depending on the chip), which can result in the
interrupt firing immediately and waking the AP.
BUG=chrome-os-partner:62224
BRANCH=none
TEST=This has been functionally tested on npcx only as that is what I
have a use case and system for, the others compile and look right but
have not been directly tested.
Change-Id: I9e0877d99e7f09f4c30bf9861fbad81c12c059ad
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://chromium-review.googlesource.com/446962
Reviewed-by: Randall Spangler <rspangler@chromium.org>
The GPIOs on npcx are handled in banks of 8, and when processing
an interrupt for a particular bank the ISR is executed for each
GPIO in the bank that has a pending bit set.
If an interrupt in a bank is not enabled (but has fired before so
the pending bit is set) but another one in the same bank is enabled
and asserts, then the ISR both of the GPIOs will be executed because
they both have pending bits set.
This results in the ISR for a disabled interrupt getting executed
when it should not and leads to unexpected behavior.
Masking the GPIOs that are not enabled means only the ISR for the
explicitly enabled GPIOs in that bank will be executed.
Example: With the Eve board we have PCH_SLP_SUS_L on GPIO(6,2) which
is enabled at init time and is in the same WKINTG_1 bank as
TRACKPAD_INT_L on GPIO(7,1) which is not enabled, but I am working
on a patch to enable it. When going into suspend PCH_SLP_SUS_L asserts,
and that is causing the ISR for both PCH_SLP_SUS_L and TRACKPAD_INT_L
to be executed. If I try to use TRACKPAD_INT_L as a wake source from
DeepS3 this means the system immediately wakes after going to sleep.
BUG=chrome-os-partner:62224
BRANCH=none
TEST=With an additional patch to enable trackpad wake from S3 on Eve,
observe that the system can enter S3 and stay there instead of immediately
waking up due to the TRACKPAD_INT_L ISR firing when it is not enabled.
Change-Id: Idc66e22c93756faf6c4319980cfb8dfe63e0dfaa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://chromium-review.googlesource.com/446524
Reviewed-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
On tablet platform, ec isn't in charge of keyboard and KSI pins are free
to use. This CL adds MIWU group and GPIO's ISR for KSI pins if there is
no keyboard scan task.
BRANCH=none
BUG=none
TEST=test all KSI pins for GPIO_INT on npcx_evb.
Change-Id: I76c8e48c067b6cb84e483eb94b104eb1998987be
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/430554
Reviewed-by: Randall Spangler <rspangler@chromium.org>
GPIO interrupts must first be enabled with a call to
gpio_enable_interrupt() to prevent ISRs from being run before
prerequiste modules are initialized.
BUG=chrome-os-partner:56486
BRANCH=None
TEST=Manual on kevin, stress test sysjump for ~1 hour (~700 sysjumps)
without failure.
Change-Id: Ia4006ef1b0c3218dfe5c92fde6713c10b0d22d2a
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/374020
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Mulin Chao <mlchao@nuvoton.com>
Add espi driver for x86-based platform which support espi interface such
as skylake and so on.
Added source:
1. espi.c: Add drivers which supports the utilities of peripheral and
virtual-wire channels so far.
2. espi.h: Add espi virtual-wire declaration for power sequence FW.
Modified sources:
1. lpc.c: Add interrupts and initialization steps for espi.
2. gpio.c: Add interrupt handler of espi reset.
BRANCH=none
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
Change-Id: Ie80afe79d85aba47fc0b72898a8374c2898ec114
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/366181
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Our UART interrupt must be able to preempt our SHI_CS interrupt,
otherwise console input may be lost. Adjust our relative IRQ priorities
to accommodate this.
BUG=chrome-os-partner:55920
BRANCH=None
TEST=Run `echo "kbpress 11 4 1" > /dev/pts/17` on kevin 200 times from
the recovery screen, verify that all input is received by the EC.
Change-Id: I36203511f5883272287ac22d0704098fbd933758
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/366622
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Mulin Chao <mlchao@nuvoton.com>
Since the pending bit of host access interrupt is set frequently if
PCH accesses KBC/PM_Channel/Shared Memory through LPC after entering
S0. It's better to add checking enable bit of MIWU of it in case huge
latency between gpio interrupt and serving its own ISR in INT11's ISR.
Modified sources:
1. gpio.c: Add checking enable bit of MIWU of host access in INT11 ISR.
BRANCH=none
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
Change-Id: I1ae57173eb208fa78218bc01cfbc91f9a29c5c81
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/352362
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Enabled CONFIG_CMD_RTC_ALARM. EC_HOST_EVENT_RTC
is enabled when the rtc_alarm goes off,
alerting the AP to transition from S3->S0.
BUG=chrome-os-partner:52218
BRANCH=None
TEST=rtc_alarm <num> and see event set in ec console
after <num> seconds. Also, check if new bit set
through hostevent command in ec before/after
rtc_alarm goes off.
Change-Id: I53b1705ce0925000f35b9f80752035d198db3310
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/345474
Reviewed-by: Shawn N <shawnn@chromium.org>
Setting NVIC_EN register is not a suitable method if you want to turn
on/off one GPIO's interrupt. Since there're eight sources belong to
the same interrupt, using MIWU_EN register which bit belongs to one
MIWU's source is a better way.
Modified sources:
1. gpio.c: Replace accessing NVIC_EN register with MIWU_EN in gpio's
interrupt utilities.
BRANCH=none
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
Change-Id: I282a45f5a3ab7cb032b2282cf7e92cacc5e706b6
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/342122
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
When a pin power-on default is input, it is necessary to configure output
level, pull up, etc. before setting the pin to output. Otherwise, the
pin may be set to an undesired logic level for a short time.
BUG=chrome-os-partner:51722
TEST=Power-up kevin, verify that CR50_RESET_L (default input, configured
as high + open drain output by default) does not go low for a short
period at boot.
BRANCH=None
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Ieaa08e14e6ea15a908f3ff4ee9188e14b17583cf
Reviewed-on: https://chromium-review.googlesource.com/335344
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Mulin Chao <mlchao@nuvoton.com>
CONFIG_SHI ("SPI host interface") has identical meaning to
CONFIG_HOSTCMD_SPS ("Accept EC host commands over the SPI slave"). Use
CONFIG_HOSTCMD_SPS, since it came first and is already defined in config.h.
BUG=chrome-os-partner:50819
BRANCH=None
TEST=`make buildall -j`
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I665c405ad72caa3b84e583a80c0893e4c625632a
Reviewed-on: https://chromium-review.googlesource.com/331342
Commit-Ready: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Add 1.8V IO support for some GPIOs and I2C pins. We use a array
(gpio_lvol_table) to confine which IO pins can switch to 1.8V. Before
setting it to support low voltage level, FW should set IO pin's type to
open-drain and disable internal pulling up or down.
We also add examples in gpio.inc of npcx_evb and npcx_evb_arm to indicate
how to set GPIO & I2C pins to 1.8V if user adds CONFIG_TEST_1P8V definition
in board.h.
In i2c.c driver, this version removes the internal pull-up feature of
i2c ports since the driving force is too weak. (about 30K ohm)
Modified sources:
1. gpio.c: Add 1.8V IO support for some GPIOs and I2C pins.
2. i2c.c: Remove internal pull-ups feature for i2c pins and move 1.8V
support to gpio.c.
3. register.h: Modified NPCX_LV_GPIO_CTL register & bits definitions.
4. npcx_evb\gpio.inc: Add examples of 1.8V IO.
5. npcx_evb_arm\gpio.inc: Add examples of 1.8V IO.
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: I73a840ae321820212e50d609dab17576117a7d64
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/330037
Reviewed-by: Shawn N <shawnn@chromium.org>
Previously the keyboard row and column pins could not use the GPIO
alternate function mechanism because their DEVALT bits were inverted
with respect to all of the others, making it impossible to correctly
configure them. With the refactor of the GPIO driver we can now add
the keyboard DEVALT entries to the gpio_alt_table, and use the
ALTERNATE macro and associated APIs to control the keyboard pin states.
The Wheatley RO firmware image is still 320 bytes smaller than before
the GPIO refactor.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Ran on Wheatley, manually verified keyboard functionality
Change-Id: Id04bc010834b5d95050b03ace6b0e1c5690757bf
Reviewed-on: https://chromium-review.googlesource.com/329762
Commit-Ready: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Body 5678901234567890123456789012345678901234567890123456789012345678901
Previously the GPIO driver used quite redundant encodings for its WUI
and DEVALT mapping tables. This refactor compresses those tables
significantly, while adding the ability to represent an inverted DEVALT
bit. The resulting RO firmware image for Wheatley is 384 bytes smaller.
This commit also corrects the interpretation of the func parameter to
gpio_set_alternate_function. Any non-negative func should be
interpreted as a request to switch a pin to an alternate mode.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
BRANCH=None
BUG=None
TEST=make buildall -j
Ran on Wheatley, manually verified basic functionality
Change-Id: I3a56a4b56d13a70a30c388e7e2c77dd7acd3838a
Reviewed-on: https://chromium-review.googlesource.com/329761
Commit-Ready: Anton Staaf <robotboy@chromium.org>
Tested-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
To get better power consumption in S0, we add FW support for
CONFIG_LOW_POWER_S0.
Before entering deep idle in S0, we must enable Host interrupt to wake up
EC if it needs to service LPC bus.
This version also add a new bit of sleep_mask (SLEEP_MASK_FAN) in system.h
to prevent EC enter deep idle if fan's duty isn't zero. Normally, the freq of
PWM fan is 25 kHz. It means we must select apb2 clock as the source clock of
PWM fan. Or fan would stop when ec enters deep idle because of no PWM signal.
In hwtimer.c, we reset the preload counter to maximum value in ITEI32's ISR
since preload counter is changed by __hw_clock_source_set all the time.
We also found there're no event set if it's deadline is over 32 bits but
current source clock isn't. To prevent ec doesn't wake-up in deep-idle even if
ITIM32 expires, FW set an event for ITIM32 after process_timers().
Modified sources:
1. wheatley/board.h: Add CONFIG_LOW_POWER_S0 definition.
2. clock.c: Enable Host interrupt for LPC.
3. clock.c: Disable LP_WK_CTL for better power consumption.
4. gpio.c: Add ISR for Host interrupt.
5. uart.c: Introduce bit 6 of USTAT to make sure transmitting is completed.
6. register.h: Add uart_clear_pending_wakeup function.
7. hwtimer.c: Fixed watchdog issue when ITIM32 is closed to overflow.
8. fan.c: Enable deep sleep if duty cycle is zero.
9. include/system.h: Add SLEEP_MASK_FAN for fan control loop.
10. core/cortex-m/task.c: Add "isb" to flash the garbage data in the
instruction pipeline.
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: Ibe3630d0d68cf3f32206adb2afa1b5958916a2be
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/324651
Reviewed-by: Shawn N <shawnn@chromium.org>
Modified hibernate funcs to support hibernate_wake_pins on weatley, npcx_evb
and npcx_evb_arm.
For better power consumption, we disable ADC, tri-state spi pins, all inputs
of wake-ups to prevent leakage current caused by input floating and set
necessary GPIOs' states in hibernate function.
Modified drivers:
1. npcx_evb/board.c: Add hibernate_wake_pins array for hibernate.
2. npcx_evb_arm/board.c: : Add hibernate_wake_pins array for hibernate.
3. wheatley/board.c: Add hibernate_wake_pins array for hibernate.
4. wheatley/board.c: Add board_set_gpio_state_hibernate func for adjusting
GPIOs' status related to board for better power consumption.
5. hwtimer.c: Remove unnecessary interrupt_enable/disable funcs. Interrupt
will disable before it is called.
6. register.h: Add WKINEN definition and declarations used for hibernate.
7. system.c: Add system_set_gpios_and_wakeup_inputs_hibernate to set GPIOs'
state and wake-up inputs before entering hibernate.
8. system_chip.h: Remove unused BBRM_DATA_INDEX_PBUTTON field.
9. gpio.c: Enable WKINEN in gpio_set_flags_by_mask func.
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: Ic85814065464095fdcb7a75964c2c528d8f8e62f
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/321466
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Enable JTAG functionality by SW without pulling down strap-pin nJEN0 or nJEN1
during ec POWERON or VCCRST reset occurs.
Please notice it will change pinmux to JTAG directly.
Modified drivers:
1. gpio.c: Remove JTAG0/1 alternative groups and bits from gpio_alt_table
2. jtag.c: Enable JTAG functionality
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Change-Id: I5a664adedeea1c75df37662dc1f3206e90163eeb
Reviewed-on: https://chromium-review.googlesource.com/306470
Reviewed-by: Shawn N <shawnn@chromium.org>
Modified i2c driver into controllers and ports to support I2C0 port 0/1 at
the same time.
Modified drivers:
1. i2c.c: Support i2c controller mechanism and fixed bug for i2c_raw functions
used by i2c_wedge and i2c_unwedge.
2. gpio.c: Fixed bug for gpio_alt_sel since wrong type of func.
3. lpc.c: Fixed bug for port80. Since disabling SUPPORT_P80_SEG, we should
replace GLUE_SDP0/1 with DP80BUF.
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: I9919269e4f5e795d9ceb8a4cd2c39abbd7bb6b1a
Signed-off-by: Ian Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/294015
Reviewed-by: Randall Spangler <rspangler@chromium.org>
npcx GPIO code calls out to an LPC function, which isn't defined on
platforms without LPC support.
BUG=chromium:520207
TEST=`make buildall -j`
BRANCH=None
Change-Id: I80c0d08fea4a2621df9646926959fc48af52a15a
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/293013
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fixed bug during polling port 0x204 by BIOS.
We should set processing flag before reading command byte in ISR to prevent
EC_LPC_STATUS_FROM_HOST and EC_LPC_STATUS_PROCESSING bits are both low.
Modified drivers:
1. gpio.c: Add LRESET ISR.
2. lpc.c: Fixed bug during polling port 0x204 by BIOS.
3. flash_ec: Reset ec before flashing ec
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: I8e557f2e2be41a7a9d40c03c775313b12668f283
Signed-off-by: Ian Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/291210
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Commit-Queue: Randall Spangler <rspangler@chromium.org>
Tested-by: Randall Spangler <rspangler@chromium.org>
Add ECST tool to modify the header used by npcx booter.
Modified drivers:
1. i2c.c: Modify for i2c_port design.
2. i2c.c: Fixed bugs when mutil-tasks use the same i2c port and pull-up issue.
3. hwtimer.c: Fixed bug whcih event expired time is behide current timer.
4. lpc.c: Add intializing host settings after pltrst is deasserted.
5. uart.c/clock.c/register.h: Fixed bug which cannot enter deep-idle
when gpio is any-edge trigger mode.
6. task.c: Add workaround method for hard fault issue.
7. keyboard_raw.c: Modified for support CONFIG_KEYBOARD_KSO_BASE
8. lpc.c: Modified for support CONFIG_KEYBOARD_IRQ_GPIO
9. lpc.c: fixed obe interrupt bug during 8042 initialization
10.Adjust path of flat files for new Makefile rules
11.Fixed build error on lpc.c without CONFIG_KEYBOARD_IRQ_GPIO
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: Icf9494174b245b4026e396be877d578f36b6f6a5
Signed-off-by: Ian Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/284036
Reviewed-by: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Commit-Queue: Shawn N <shawnn@chromium.org>
Add npcx_evb_arm board-level driver for arm-based platform.
Add header.c: for booting from NPCX5M5G A3 Booter.
Remove lfw folder due to those functionalitie have been replaced with Booter
Modified drivers for
Patch Set 1:
1. flash.c: Implement UMA lock, tri-state and selection register lock functionalities
2. hwtimer.c: Add ITIM32 for hwtimer
3. lpc.c: Add checking for LRESET
4. system.c: Modified CODERAM_ARCH functions for NPCX5M5G A3 Booter.
5. uart.c: Add support for module 2
Patch Set 2:
6. lpc.c: Modified lpc_get_pltrst_asserted() func
Patch Set 3:
7. minimize the changes for CONFIG_CODERAM_ARCH in common layer
8. comments of Patch Set1/2
Patch Set 4:
9. Modified CONFIG_RO_MEM_OFF point to ro image and keep header as a part of ec.RO.flat.
10. Fixed RO_FRID and RW_FRID issues which caused by CONFIG_CODERAM_ARCH.
Patch Set 5:
11. Modified system.c in common folder for supporting *_STORAGE_OFF.
12. Use *_STORAGE_OFF in firmware_image.lds.S to indicate flat file layout in flash.
Patch Set 6:
13. rebase to newest version
14. system.c: Modified for the newest include/system.h
Patch Set 7:
15. Merge from version 0625
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: Ifd7c10b81b5781ccd75bb2558dc236486976e8ed
Signed-off-by: Ian Chao <mlchao@nuvoton.com>
Reviewed-on: https://chromium-review.googlesource.com/272034
Reviewed-by: Shawn N <shawnn@chromium.org>
Tested-by: Shawn N <shawnn@chromium.org>
Commit-Queue: Shawn N <shawnn@chromium.org>
In the gpio_info struct, we had a irq_handler pointer defined even
though a majority of the GPIOs did not have irq handlers associated. By
removing the irq_handler pointer out of the struct, we can save some
space with some targets saving more than others. (For example, ~260
bytes for samus_pd).
This change also brings about a new define:
GPIO_INT(name, port, pin, flags, signal)
And the existing GPIO macro has had the signal parameter removed since
they were just NULL.
GPIO(name, port, pin, flags)
In each of the gpio.inc files, all the GPIOs with irq handlers must be
defined at the top of the file. This is because their enum values from
gpio_signal are used as the index to the gpio_irq_handlers table.
BUG=chromium:471331
BRANCH=none
TEST=Flashed ec to samus and samus_pd, verified lightbar tap, lid, power
button, keyboard, charging, all still working.
TEST=Moved a GPIO_INT declaration after a GPIO declaration and watched the build
fail.
TEST=make -j BOARD=peppy tests
TEST=make -j BOARD=auron tests
TEST=make -j BOARD=link tests
Change-Id: Id6e261b0a3cd63223ca92f2e96a80c95e85cdefb
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://chromium-review.googlesource.com/263973
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Commit-Queue: Aseda Aboagye <aaboagye@chromium.org>
Trybot-Ready: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Alec Berg <alecaberg@chromium.org>
Issues fixed on 0216:
1.Modified CONFIG_KEYBOARD_COL2_INVERTED support in keyboard_raw.c
2.Modified warm_reset checking in gpio.c
3.Modified system_get_chip_name in system.c for package info.
4.Modified fan.c and pwm.c for:
● If the DCRn value is greater than the CTRn value, the PWM_n signal is always low.
● Fan stall condition event:
If the measured fan speed is lower than the lowLimit value (unless the Fan Speed Low Limit value is 0) or in case of erroneous measurement, the userCallback is called.
5. Change cycle_pluses to 480 in board.c
Issues fixed:
1. Jump data at top of RAM is getting corrupted. Changed the flag to
RESET_FLAG_RESET_PIN. Added a workaround method to fix VCC1_RST
issue.
2. Hibernate wake need to report whether wake reason was GPIO or RTC
3. Hibernate wake must be distinguishable from watchdog reset. The
booter will log reset reason in Code RAM. I copy the log data to
battery-backup RAM in little FW. And system driver will refer this
data to distinguish if it's watchdog reset or not.
4. Watchdog reset flag is not set. Same fix as 3.
5. Should return error if unable to clear SPI flash status register.
6. Remove chip_temp_sensor.c
7. Remove use of pstate from flash driver
8. Remove support for watchdog warm reset
9. Keyboard raw driver must support COL2 inverted
10. LPC memory mapped data must be read-only from host
11. LPC should support PLTRST# signal
12. Problems reading chip type/version. Use core registers and ROM data to read IDs.
13. When chip type/version is unknown, report hex value.
14. Watchdog does not consistently print panic information.
15. Remove console force enable logic.
16. Enable only the peripheral clocks that are needed. Please notice
user should add bit mask in CGC_XXX_MASK if they want to enable
additional module. For example, if user wants to enable PWM3, he must
add PWDWN_CTL2_PWM3_PD bit in CGC_PWM_MASK.
Please see HOOK_FREQ_CHANGE and HOOK_INIT these two hook functions.
If I turn off all I2C modules in system_pre_init and turn on the
modules I need in i2c_init, I found its freq is not correct. The root
cause is hook_notify(HOOK_FREQ_CHANGE) is executed first (in
clock_init) before i2c_init. At this time, i2c modules are power-down
and writing to freq register is useless. I re-execute freq-changed
hook function after turning on modules again.
17. MPU properly configured to prevent code execution from data RAM
18. Partial nvcontext implementation. Copy these 16 bytes in our battery-backup RAM.
Additional items we also modified:
1. pwm.c: Support open-drain IO type of PWM. (PWM IO-Type cannot by
determined by GPIO, we use bit 1 & 2 of function byte of gpio_alt_func
array to support it)
2. ec_npcxflash.c: Use definition to replace constant value. Stop
watchdog during flash programing.
3. npcx_cmds.tcl: Adjust script sequence for robustness. Add unlock
MPU commands for Data RAM.
BUG=chrome-os-partner:34346
BRANCH=none
TEST=manually verify changes
Change-Id: I722a77d29e7543b054819480c7b7477af4263119
Signed-off-by: Ian Chao <mlchao@nuvoton.com>
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/248670
Add npcx_evb in board folder for testing
Add shared-spi arch support in common layer.
Modified drivers for
1. Fan.c: console command “pwmduty”.
2. Pwm.c: for the issue when set duty to 0.
3. System.c: for hw reset only during system reset.
4. Flash.c: Fixed access denied bug of the flash driver for host command.
5. Comments from Patch Set 1
6. Comments from Patch Set 3 (except sha256.c)
7. Add openocd and flash_ec support for npcx_evb
8. Add little FW and spi-flash upload FW in chip folder
9. Add optional make rules for PROJECT_EXTRA
10.Replace CONFIG_SHRSPI_ARCH with CONFIG_CODERAM_ARCH and remove changes
in common layer sources for shared-spi arch. (except sysjump)
11.Find the root cause of JTAG issue and use workaround method
with SUPPORT_JTAG in clock.c
12 Execute hibernate in low power RAM for better power consumption
13 Add workaround method for version console command
14 Modified coding style issues by checkpatch.pl tool
BUG=chrome-os-partner:34346
TEST=make buildall -j; test nuvoton IC specific drivers
BRANCH=none
Change-Id: I5e383420642de1643e2bead837a55c8c58481786
Signed-off-by: Ian Chao <mlchao@nuvoton.com>
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/233742
